Disco 2 Td5 troubles

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
BlueBeauty

BlueBeauty

Member
Posts
72
Location
Penrith, Cumbria.
Hi guys, got a strange issue that comes and goes. When driving, just everyday driving, the disco seems to be "miss firing" and judders like hell, this has happened, when starting out or mid drive and once at 70 on the motorway (not good) turn the whole lot off and leave it for 30 seconds or so and start her back up again problem gone, some times for 10 minutes sometimes for weeks. The only consistency I've noted is I think I'm on about a 1/4 tank of juice each time. I'm still very new to landy care and have very limited knowledge, but I'm learning. Has anyone experienced this or have and ideas? I'd really appreciate any help with this. Many thanks in advance BB.
 
Didn't think of checking the tank breather, checked main air filter and air intake and banged a new MAF unit in as that wasn't looking well. I'll check the breather and harness and see if that tells me anything.
Thank you for the advice and quick response Jonny, top bloke. BB
 
I would say the easiest way to distinguish between myself and Blue Beasty would be that I'll be the one asking for advise rather than the one giving it out! But so save confusion I'll change the way I sign any text
 
Hi, Is there anyone near you that can put it on a Nanocom or similar to rule out the injector harness?
Griff (Too far away!)
 
Not sure, I'm guessing that local landy spots could probably hook it up to one or something similar, was hoping to check as much as I myself first before fork out garage prices. Unless anyone is in the Penrith area that's reading this and could lend a hand in exchange for some bottles o' beer and maybe a meat pie!?
 
Update:
On advise from Griff I've been in touch with a mate of mine whose a aggie mech so has diagnostics for a Td5, so Sunday morning I'll get her plugged in and get under it whilst I'm there to have a look at the breather. Will post what I find. Beaut
 
The saga continues:
So it's time for a new injection harness! As you all predicted, old harness brittle connectors, brittle Orings and brittle seals, oil in the connections, oil in the harness, oil in the red plug, oil in everything!! Except inside the ECU, so that's something! Cleaned everything old re-sealed and she ran like a dream.... for about an hour then back with a vengeance came the juddering and power loss, ah well will get some new bits, get them whacked in and see what's next, think I have a way of sealing up the harness better, will have a go and post pics of what I do. Thanks again for the advice all, was a big help. Can anyone recommend/provide a link for a new harness, seen them priced between £23 and £98 which seems rather a lot! Cheers folks Beaut.
 
Some people have had problems with pattern harnesses - it's best to get genuine. As Brian says, it can take some time for the oil to run right through.
I've taken the white spacer out of the ECU end red plug and drilled a hole so if any oil does get through it has a faint chance of draining out. But I changed the harness 5 years ago and the plug has remained dry since.
 
Are you sure it isn't in the ECU? If it is, even a small amount can cause issues. I took mine off and stood it socket face down over night on some paper towels. I also sprayed loads of electrical cleaner into the plug under the rocker housing every night for a week or so to chase the oil out of the wiring.
 
Yup, the inside of the ECU was as clean as a whistle, red plug was dripping in it but it seems to of stopped it from getting all the way through, already dowsed the red plug and the whole of the loom and connectors in electrical cleaning fluid, but didn't dig the white plastic out of the red plug, so that will be done this eve and I'll give the loom housing another flush through whilst I'm at it. Having trouble souring a genuine LR injector loom as suggested, anyone know who stocks them? Beaut
 
BlueBeauty said:
Yup, the inside of the ECU was as clean as a whistle, red plug was dripping in it but it seems to of stopped it from getting all the way through, already dowsed the red plug and the whole of the loom and connectors in electrical cleaning fluid, but didn't dig the white plastic out of the red plug, so that will be done this eve and I'll give the loom housing another flush through whilst I'm at it. Having trouble souring a genuine LR injector loom as suggested, anyone know who stocks them? Beaut
Click to expand...

Even the closest inspection of the loom won't show the oil contamination. It doesn't run down the wires as you would think, but down between the actual copper of the wires and the inside of the insulation by capillary action. The only way to get it out of the loom again is by gravity and capillary action again but cleaning the plug will help.
 
Right o' I gotcha, well I just keep cleaning things out from the red plug end as it "drains" down and hopefully over time I'll get it back right again, thanks for the help and advice Brian.

Griff that's great thanks mate, I'll give him a call at some point this week, cheers bud. Beaut
 
It might be easier to clean out the harness when its warm.
I used an old Aquavac to help suck out the oil from the loom, and wrapped my hand around the plug to create a sort of seal.
Worked ok, oil has never re-appeared in the red plug.
Mark
 
You must log in or register to reply here.

Similar threads

N
Limp mode
Replies
0
Views
232
Nickandstan
N
Keith_L
Disco 2 3 Amigos - sort of
Replies
3
Views
415
Keith_L
Keith_L
PopPops
Disco 2 TD5 Mahle oil filter
Replies
4
Views
303
PopPops
PopPops
sonicm1etn
intermittent completely dead fault TD5 D2
Replies
7
Views
436
Shedload
S
L
Very strange smell
2
Replies
20
Views
929
Stanleysteamer
Stanleysteamer
Back
Top