td5 straight through pipe
- Thread starter torlak
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
DIFFLOCK66
Well-Known Member
- Posts
- 3,249
- Location
- Chipping, Lancashire
Wish i could help, but my local garage fitted it for me so no idea - they just sorted out the nuts etc.
sierrafery
Well-Known Member
- Posts
- 17,872
- Location
- Arad/Romania
i'm happy with mine, you'll not find these things in RAVE but here Allbrit.de - Ersatzteile für LAND ROVER & MG ROVER , if you gogle out the part number (nr5) you'll see ... M10
... if you want other bits click on "Back to navigation" or "Land Rover catalogue"(for other types) at the top of page
... if you want other bits click on "Back to navigation" or "Land Rover catalogue"(for other types) at the top of pagei'm happy with mine, you'll not find these things in RAVE but here Allbrit.de - Ersatzteile für LAND ROVER & MG ROVER , if you gogle out the part number (nr5) you'll see ... M10
raise:
DIFFLOCK66
Well-Known Member
- Posts
- 3,249
- Location
- Chipping, Lancashire
Yep - happy with mine too!
joojar
Active Member
- Posts
- 158
- Location
- Derbyshire
Same here
The sound is wonderful - I've seen some describe it as boomy, but to me its more 'grunt' with a lovely top-note of turbo chirrup. Certainly been driving with a big smile since switching to the straighty
The sound is wonderful - I've seen some describe it as boomy, but to me its more 'grunt' with a lovely top-note of turbo chirrup. Certainly been driving with a big smile since switching to the straighty
gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
I am more than happy with the sound of mine,everyone comments on how throaty it sounds.
gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
unless it is in great condition,then bin it.they are cheap enough to buy anyway.good luck fitting the new pipe,will be worth it.
Orch
Active Member
- Posts
- 626
- Location
- Salisbury area
I kept mine and glad I did, after a while I put it back on and went for a straight through rear section instead (side exit). Completely different sound.
Although I'm now considering putting the middle pipe back on to make full straight through :flame2:
Td5D2
New Member
- Posts
- 28
- Location
- Hampshire, England
I found that the studs on the rear section of mine were completely unusable. I had to cut them off and drill 10mm holes in it and use M10 bolts and nuts to bolt it up.
I did this for the mid to de-CAT section too.
As above, the sound is amazing. You can actually hear the turbo working now. It is a little boomy sitting in the back though.
I did this for the mid to de-CAT section too.
As above, the sound is amazing. You can actually hear the turbo working now. It is a little boomy sitting in the back though.
dale4mud
New Member
- Posts
- 49
- Location
- Peterborough
I'm looking to do this... Does it give you any more grunt as mine is feeling a little flat, new airflow sensor improved it but I think my cat may be blocked?
gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
what year is your td5?
dale4mud
New Member
- Posts
- 49
- Location
- Peterborough
It's an 04 mate
gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
ok.
thebiglad
Well-Known Member
- Posts
- 7,387
- Location
- Central France
If you're sure that you have a cat in your exhaust downpipe, then just replace that component on it's own and the engine will breath much better without making it too noisy.
If the engine is running a bit flat, have you cleaned the MAP sensor on the inlet
manifold?
Have you checked the red plug on the main engine ECU for oil contamination?
Dave
dale4mud
New Member
- Posts
- 49
- Location
- Peterborough
I've checked the looms for oil contamination and I'm happy to say they're bone dry
I'll check the MAP tomorrow I think
Thanks for the good advise
