Salisburylander
Active Member
- Posts
- 259
- Location
- Salisbury
I’m worried about replacing the fuel filter on my TD5. It’s not the actual replacement itself but the priming and starting afterwards. Any tips before I give it a go?
Disco 2 TD5 fuel filter replacement
- Thread starter Salisburylander
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
fill filter as much as pos before fitting,start it hold throttle half open till your sure its purged, if it wont start switch ignition on press throttle pedal 5 times fully till engine light flashes leave for 5 mins then try and start if not repeat
Salisburylander
Active Member
- Posts
- 259
- Location
- Salisbury
Cheers for the info. I’ll nip and get some diesel before I start.
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
there 2 washers on the filter ensure the center one comes off it often sticks to filter head
BravoNovember
Active Member
- Posts
- 131
- Location
- The Shire
Remembered this at the last minute last weekend, filter full of diesel in hand.
BravoNovember
Active Member
- Posts
- 131
- Location
- The Shire
I found the priming process above not too bad, filled the filter up. I’ve read some people fill it 2/3 diesel 1/3 redex, I’m not sure what the benefit is there or the potential pit falls so I just used diesel.
I switched the ignition on and left it for about a minute, turned it off for a bit, did the same whilst pumping the pedal a few times then she started first time. Good job, my mate was filming me and would have ripped me for weeks otherwise.
I switched the ignition on and left it for about a minute, turned it off for a bit, did the same whilst pumping the pedal a few times then she started first time. Good job, my mate was filming me and would have ripped me for weeks otherwise.
Salisburylander
Active Member
- Posts
- 259
- Location
- Salisbury
Filled the filter with diesel, screwed it in, let it prime and it started first time.
I was really worried about doing the filter cos my colleague tried to do his and I’m not sure what he did wrong but his car ended up being transported to a garage...
I was really worried about doing the filter cos my colleague tried to do his and I’m not sure what he did wrong but his car ended up being transported to a garage...
Landmark2
Well-Known Member
- Posts
- 824
- Location
- Shropshire
Always done it the same way - fill with diesel/re-fit/ignition on and let it bleed for a few mins/ then start. Never needed to use bleed cycle.
Griff
Griff
sierrafery
Well-Known Member
- Posts
- 18,267
- Location
- Arad/Romania
I've never filled the filter myself just swapped it and started without probs all the time after the purge
+1
I have done it also 2 times without filling. After the purge cycle started without issue.
Bobdog
Well-Known Member
- Posts
- 4,286
- Location
- Horsham West Sussex
Replaced mine today, my fuel pump was whining loudly over a few days and I thought the pump was on its way out. Recently had head gasket and turbo replaced and it wasn't performing as it should, so gave it a shot of cataclean which improved it somewhat. The cataclean must have cleaned loads of shíte out which ended up in the filter. Anyway, changed it today and the pump is much quieter and a very noticeable performance improvement.
To clarify the purge cycle - ignition on (pos 2) allow pump to prime, pump pedal 5 times and purge cycle begins. (Primes 5 times). No need to fill filter with diesel.
To clarify the purge cycle - ignition on (pos 2) allow pump to prime, pump pedal 5 times and purge cycle begins. (Primes 5 times). No need to fill filter with diesel.
