Disco 2 TD5 03 running , died , No restart ..

Estonian blue · Jan 31, 2017

Hi all, any ideas why it won't start? Checked for fault codes with a generic tester, none,
We have diesel, had gone through purge process and have black smoke on cranking, sounds like one or two cylinders firing, good crank speed , etc but that's all....
It had been running fine and was driving ok, petered out according to wife like it was out of fuel but a bit to quick, The injector wiring harness was changed 3 years ago ...
Only thing I noticed recently that it would idle at 1000 instead of 800, sometimes it would drop to 800 after tapping the throttle , being jobless just now it'd be great if anyone can point me in some sensible test directions without having to resort to the , the dddd dealer

.
If you can ...thanks..Michael

biggeeeee · Jan 31, 2017

Can you hear the fuel pump in the diesel tank running?
One test would be to remove the fuel filter (in the right hand rear wheel arch) and see if fuel is being pumped through from the tank

RyanDay1 · Jan 31, 2017

What generic tester did you use? i'll be the first to say that there are only a select few readers that are properly compatible with a td5

Others likely wont give you anything useful

biggeeeee · Jan 31, 2017

and your Generic tester won't work on a TD5

Estonian blue · Jan 31, 2017

Have fuel flow, I checked on the roadside as you suggested, I think I used this tester on a previous td5 and had **** loads of old faults , but I'll go check its name ...it went through it normal cycle detected can bus , if. I recall right ..

neilly · Jan 31, 2017

You can have a look at these videos on youtube.

Iirc , there are 3 of them.

Cheers

neilly · Jan 31, 2017

Estonian blue said:
Have fuel flow, I checked on the roadside as you suggested, I think I used this tester on a previous td5 and had **** loads of old faults , but I'll go check its name ...it went through it normal cycle detected can bus , if. I recall right ..

Is it an Auto?

Cheers

Estonian blue · Jan 31, 2017

The scanner is a u480 obd11/eobd11 memo scanner. From the book it suggests that around 2004 many eu light diesels had to be obd11 compliant as my wonderful when it works car is 2003 , I wonder if this late model is ..wonder I said, I'm allowed to wonder ... what do u think I'm in cloud cuckoo land and need to find someone with a what ? Code reader ? Cheers .

Estonian blue · Jan 31, 2017

Yes it is an auto , which sounds like you have a sneaky idea ? I ll go look at the vids, thank you .

neilly · Jan 31, 2017

Ref the code reader, I am sure @brian47 Oooops, or even @biggeeeee , is already writing the reply, but chance is you are unlucky with that one.

Ref the Auto, you mentioned Can bus, but it is worth making sure others know about it being an Auto, I am not au fait with them,only thing I would ask is there anything strange on the dash ?

Cheers

Discodevon · Jan 31, 2017

It's probably the fuel pump?

brian47 · Jan 31, 2017

neilly said:
Ref the code reader, I am sure @brian47 Oooops, or even @biggeeeee , is already writing the reply, but chance is you are unlucky with that one.

Ref the Auto, you mentioned Can bus, but it is worth making sure others know about it being an Auto, I am not au fait with them,only thing I would ask is there anything strange on the dash ?

Cheers

Who taketh my name in vain?

Yes, you are correct, the diesel Discovery did not become fully OBDII compatible until mid 2004 with the release of the Discovery 3. Petrol Discos were compatible a few years earlier.
Most Disco owners who do have a code reader will tell you to use either Nanocom, Hawkeye, Lynx or Testbook. With the exception of the Testbook, these days they're very similar in capability and price; a couple of hundred GBP. Testbook is the main dealer's diagnostic equipment so that's lots and lots of pounds! Even though there's an OBDII type socket under the dash, the protocols weren't compatible.
You might be lucky and find a generic code reader that will give you some results, but to be honest, how do you know if it's even telling the truth? And it'll probably only partly read the engine ECU and won't even communicate with any of the other ECUs on the Disco 2.
With regards to CAN-BUS, I don't think there's much, if any canbus connected kit on the Disco 2, at least, I've not come across any. I think that that came in on the Disco 3 too. Even in the area of the auto gearbox, it think it's just ordinary switching with static electrical loads, nothing fancy.

markomate2 · Jan 31, 2017

Tere ohtust Michael!
Kus sa oled?
Ma olen Tallinas praegu.
Kajuks, minu Eesti keelt ei hasti!
Aga sinu Inglise keelt vaga hasti!
So in English.
If your around Tallinn, Im here until Monday.
Looking after a daughter with flu so may not be able to get out but happy to chat if you want?
Just message me your number if you want me to call.
Head ööd!
Mark

brian47 · Jan 31, 2017

markomate2 said:
Tere ohtust Michael!
Kus sa oled?
Ma olen Tallinas praegu.
Kajuks, minu Eesti keelt ei hasti!
Aga sinu Inglise keelt vaga hasti!
Head ööd!
Mark

And you can't say fairer than that!

Disco 2 TD5 03 running , died , No restart ..

Estonian blue

Member

biggeeeee

Retired - Living the dream

RyanDay1

Well-Known Member

biggeeeee

Retired - Living the dream

Estonian blue

Member

neilly

Well-Known Member

neilly

Well-Known Member

Estonian blue

Member

Estonian blue

Member

neilly

Well-Known Member

Discodevon

Well-Known Member

brian47

Well-Known Member

markomate2

Well-Known Member

brian47

Well-Known Member

Similar threads