Looking very nice!
thanks! Come up ok for a cheap fix didn’t it
Steep learning curve
- Thread starter resto_d1
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
thanks! Come up ok for a cheap fix didn’t it
Well, I’m going a bit loopy through lack of contact with anyone. I’ll let you know when the dog starts talking back.
I look forward to walking around the corner and getting a fresh pint of staropramen.
The good thing is, these projects keep you busy. When I’m not working I’m on it which is brilliant for the mind. Annoying I have run out of gas though! As the post service is still working I can order the bits I need mech wise so I began on that.
I’ve decided to whip head off and replace hg and give the head a refresh. I made this decision after seeing this!
Water pump wasn’t horrendous with a bit of corrosion on blades but it’s clearly in need of a bit of tlc and a new rad!
I look forward to walking around the corner and getting a fresh pint of staropramen.
The good thing is, these projects keep you busy. When I’m not working I’m on it which is brilliant for the mind. Annoying I have run out of gas though! As the post service is still working I can order the bits I need mech wise so I began on that.
I’ve decided to whip head off and replace hg and give the head a refresh. I made this decision after seeing this!
Water pump wasn’t horrendous with a bit of corrosion on blades but it’s clearly in need of a bit of tlc and a new rad!
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
no gasket will seal it,lack of anti freeze at some point
Oh whilst you’re on @jamesmartin
bores look bang on to me with honing marks still in place! Gasket was a 0 hole job but can’t see any machining stamps or marks on head yet...
bores look bang on to me with honing marks still in place! Gasket was a 0 hole job but can’t see any machining stamps or marks on head yet...
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
yes look good
measure the valve stand down and piston protrusion if you can
https://workshop-manuals.com/landrover/300tdi/overhaul/cylinder_head/valve_head_stand_down_checking/
measure the valve stand down and piston protrusion if you can
https://workshop-manuals.com/landrover/300tdi/overhaul/cylinder_head/valve_head_stand_down_checking/
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
a straight edge and feeler gauges, though a decent steel rule would suffice for what you need
RAW111111
Well-Known Member
- Posts
- 255
- Location
- Nottingham
Hicap phill
Well-Known Member
- Posts
- 16,237
- Location
- Wiltshire
You doing the stem seals while your that far in?
Yes mate think they come in a decoke kit. I haven’t used valve removal tool for about 8 years and can’t seem to find it so got to order a new one.
Last engine I did was a DOHC 20v on bodies - doing this has made me realize just how simple 300tdi is. Tough and built for a job! The fact that you can get head off in couple hours with no need to touch cams was lovely!
I don’t know how good the kit will be - bearmach I think but will be Elring no hole HG
Last engine I did was a DOHC 20v on bodies - doing this has made me realize just how simple 300tdi is. Tough and built for a job! The fact that you can get head off in couple hours with no need to touch cams was lovely!
I don’t know how good the kit will be - bearmach I think but will be Elring no hole HG
Cheers mate. I love doing this stuff. Welding is must and a bit of a graft but love Stripping and building up mechanical stuff
- Posts
- 68,227
- Location
- The Wooly Witch
Thanks - it’s absolutely shot. Yeah it’s one of the old ‘they don’t make em like the used to’ isn’t it!
