Spiggot bearing question

D

David g4yvm

Active Member

Posts

97

Location

Salisbury

• Sep 17, 2024

• #1

My son and I have bought a Defender 90 as a doer-upper and have found a 'yikes' issue. He says its a missing spiggot bearing (forgotten by previous owner) I havent a clue. Hoorid rattling from where the spiggot bearing lives when engine idels and clutch pedal UP. Depress clutch pedal, noise stops.

Any thoughts from that scarce info?

David

 

tottot

Well-Known Member

Posts

8,028

Location

west wales coast

• Sep 17, 2024

• #2

With out the spigot bearing [ which is just a plain bush] in place the input shaft to box and clutch plate would tend to move about some, this would be when clutch is in. Result is likely the gearbox input shaft bearing wearing over time making noise or plate itself getting loose on the shaft I recon. When pedal down shaft stops turning so no noise. Load when driving likely reduces noise.

 

boguing

Well-Known Member

Full Member

Posts

10,369

Location

A bit sarf of Dorking

• Sep 18, 2024

• #3

How does he know it's missing?

 

freelance

Well-Known Member

Posts

8,685

Location

essex and beyond

• Sep 18, 2024

• #4

Gearbox input shaft bearing more like

 

tottot

Well-Known Member

Posts

8,028

Location

west wales coast

• Sep 19, 2024

• #5

boguing said:

How does he know it's missing?

Click to expand...

Did he say "forgotten by previous owner" or was that just a guess. More likely the clutch release bearing I recon.

 

miktdish

Guns n Chainsaws

Full Member

Posts

4,544

Location

Near Lanark, South of Glasgow. Scotland

• Sep 19, 2024

• #6

Bronze spigot bearing (in the very center of the flywheel) ..
The gearbox input shaft sits in it,

Yes the flywheel is pants, yes I had it skimmed (-17mm) before it was refitted.

 

Tim4x4

Well-Known Member

Posts

2,200

Location

In the shed

• Sep 19, 2024

• #7

miktdish said:

Bronze spigot bearing (in the very center of the flywheel) ..
The gearbox input shaft sits in it,

View attachment 326302

Yes the flywheel is pants, yes I had it skimmed (-17mm) before it was refitted.

Click to expand...

-17mm !!! That was radical.

 

miktdish

Guns n Chainsaws

Full Member

Posts

4,544

Location

Near Lanark, South of Glasgow. Scotland

• Sep 19, 2024

• #8

Yes it would have been ... 17thou.

 

dag019

Well-Known Member

Posts

6,099

Location

Warwick

• Sep 20, 2024

• #9

miktdish said:

Yes it would have been ... 17thou.

Click to expand...

this new fangled metric system is awfully confusing especially when people still use old fashioned measurements as well.

 

miktdish

Guns n Chainsaws

Full Member

Posts

4,544

Location

Near Lanark, South of Glasgow. Scotland

• Sep 20, 2024

• #10

Yes, I apologise, I slipped ...

 

Tim4x4

Well-Known Member

Posts

2,200

Location

In the shed

• Sep 20, 2024

• #11

miktdish said:

Yes it would have been ... 17thou.

Click to expand...

I have lightened a few flywheels but not like that. 0.017" looks better

 

Last edited: Sep 20, 2024

D

David g4yvm

Active Member

Posts

97

Location

Salisbury

• Sep 28, 2024

• #12

tottot said:

Did he say "forgotten by previous owner" or was that just a guess. More likely the clutch release bearing I recon.

Click to expand...

He did say that as a guess because he knew there’d been a rebuild.
He’s gone through everything now other than this bearing to get the mot so that’s next I guess if the noise persists. We shall see. The vehicle will be sold though as that was always its point. But not sold in a dodgy way.