Sitec's Cummins powered 101!

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
reading these threads makes me want to do another cummins, but it seems like its gone from a conversion that shocked everyone:D (14 years ago!)to everyone has heard of and is doing:(

Which means Ive got to think of something far madder to fit or make my own high strength transfer box and dana 60 portals:D
 
Langers said:
Yup, when I first rode in it, the power and noise was so immense that I went partially blind.

Although that might have had something to do with the injectors leaking diesel straight onto the exhaust manifold :rolleyes:

And RE: Cummins one-oh-ones, I'm not sure yet whether to build ultimate Cummins 101 or ultimate Cummins 110 DCPU. But now that my Td5 has been sold I'm in the position to make an acquisition, if you understand :)
Click to expand...

Great position to be in!!! :)
 
A bit more progress over the last few days... Here's the rear spare carrier, now with the two support pillars in place. Each pillar has its top piece sat in place.. These will carry the 100 x 50 RHS that will carry the spares, a couple of work lights and poss a few ariels. :)
 

Attachments

  • image.jpg
    image.jpg
    245.5 KB · Views: 600
Here we are setup 4 hours north of home at the South Australian Land Rover Show in Melrose. We had a great run up, running at 60mph most of the way, and at 70mph once out in the country! The 101's really stable at these speeds, and we even outran a Puma110 on the next hill after he'd overtaken us! He didn't look happy!!!:p
 

Attachments

  • image.jpg
    image.jpg
    174.2 KB · Views: 633
Yesterday, we took part in a small group tour into the surrounding hills on a large wine producing property. Some of the slopes tackled were half a km long and 45deg up or down. Second low box with the Cummins at idle was the speed of choice! Awesome sound, torque and usability! I did have one 'oh crap' moment going up the steepest slope with an awful lot of nothing behind us... The thought of my welded gear and two welded props came to mind... Knowing that 101 brakes in reverse are all but useless, and with my 'average' handbrake, had a prop broken, we'd have been on a roller coaster!! A fast one at that!!! :D
 

Attachments

  • image.jpg
    image.jpg
    201.4 KB · Views: 469
sitec said:
Yesterday, we took part in a small group tour into the surrounding hills on a large wine producing property. Some of the slopes tackled were half a km long and 45deg up or down. Second low box with the Cummins at idle was the speed of choice! Awesome sound, torque and usability! I did have one 'oh crap' moment going up the steepest slope with an awful lot of nothing behind us... The thought of my welded gear and two welded props came to mind... Knowing that 101 brakes in reverse are all but useless, and with my 'average' handbrake, had a prop broken, we'd have been on a roller coaster!! A fast one at that!!! :D
Click to expand...

you got a compression/exhaust break on the cummins?
 
Well, the 101 is now well tested. We've covered over 2000km in the last few weeks and the only issue was a loose terminal on the rear of the IGN key switch which temporarily ceased forward motion for a few min! The Cummins performed fantastically, with good speed on the blacktop, and awesome torque and usability off road!! Fuel consumption was brilliant for a 101 coming in at between 11.5 to 12.0 LT/100km. A very happy 101 owner, with a 101 that's now affordable to use!! :p
 

Attachments

  • image.jpg
    image.jpg
    219.4 KB · Views: 552
So, now the nights are setting in here, and the 101 has become the daily driver, I've found I need better lights, and sooner rather than later!! I've got back into the 'Quad Light Bumper' build! Here's the basic shape so far.
 

Attachments

  • image.jpg
    image.jpg
    246.5 KB · Views: 501
Here's the center plate, that sits directly below the front grille. This is fairly thick at 10mm, but forms the top of the sunken center clevis, and also the baseplate for the two winching/recovery points. This plate will be directly linked to the chassis rails via the side plates.
 

Attachments

  • image.jpg
    image.jpg
    251.9 KB · Views: 473
Here's the underside/internal bit of the recessed clevis. There'll be a hole cut in the center of the bumper to form the jaw. I have some Ebay 'Halo/Angel Eye' lights coming for the outer two lights. $100.. If they're crap, they can go on the inside, and I'll buy some std 7" headlights and some HID globes. :)
 

Attachments

  • image.jpg
    image.jpg
    247.2 KB · Views: 401
Was watching a 6BT on ebay as our Isuzu lump needs replacing, don't think we have the time or energy to put a 6BT in the hole though! :eek:

The search continues for a measley 3.1TDI...
 
Ah go on go on go on!! You know you would love it!!!! Did a 120km round trip down to Adelaide in mine today, and was laughing like a teen every time I launched it off the lights and startled the fancy fourbys that thought they'd leave me for dust!!!
 

Attachments

  • image.jpg
    image.jpg
    61 KB · Views: 471
You must log in or register to reply here.

Similar threads

G
You might know me as MilitantGraham
Replies
5
Views
359
saxavordian
saxavordian
yfo866
Is the 101 Forward Control Club & Register no more?
Replies
10
Views
2K
Therapy Required
T
yfo866
Early 3.5 Range Rover cruise control?
Replies
9
Views
1K
hef19898
hef19898
throwyourbike
Potential New Owner
2
Replies
30
Views
1K
WhiskyLassie
WhiskyLassie
yfo866
101 swivel hubs, grease or oil?
Replies
3
Views
2K
tottot
tottot
Back
Top