major truma 2
New Member
- Posts
- 525
- Location
- rotherham
as title ,,please
series diesel engine
- Thread starter major truma 2
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Chris W
Well-Known Member
- Posts
- 2,311
- Location
- Manchester
get a 2.5 n/a cheap as chips, and a straight drop in 
major truma 2
New Member
- Posts
- 525
- Location
- rotherham
got a price mate ?,
chips are about 1pound 20 for a big bag round here lol
chips are about 1pound 20 for a big bag round here lol
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
local place may have a 2.25 petrol in need of an overhaul
major truma 2
New Member
- Posts
- 525
- Location
- rotherham
major truma 2
New Member
- Posts
- 525
- Location
- rotherham
Bump
michaelwhite
New Member
- Posts
- 27
buy my discovery 200 tdi and fit the engine t&t drive home
t&t drive home
flat
Well-Known Member
- Posts
- 9,075
- Location
- Far away from you!!
buy my discovery 200 tdi and fit the engine
You need 50 useful posts before you can sell on the forum fella
Chris W
Well-Known Member
- Posts
- 2,311
- Location
- Manchester
wolf has one
also have a look here http://www.landyzone.co.uk/lz/f59/whats-worth-256891.html#post3061872
Last edited:
lordluke1995
New Member
- Posts
- 628
Defender 2.5na for sale low Milage with video of running on hand
Freetime101
Active Member
- Posts
- 358
- Location
- North East
I've got a 2.25 diesel still in the truck, it's coming out in favour of a 200tdi when I find one I can afford.
How much are you planning on spending?
How much are you planning on spending?
- Posts
- 10,639
- Location
- Oxfordshire
mine's still about
major truma 2
New Member
- Posts
- 525
- Location
- rotherham
all sorted now ,thanks peeps ,,ive gone for a 300 tdi instead
Chris W
Well-Known Member
- Posts
- 2,311
- Location
- Manchester
- Posts
- 10,639
- Location
- Oxfordshire
interesting.. you fitting with or without turbo?
you'll have to weld on engine mounts (get em from the donor) and there's a fair bit of fiddling iirc
you'll have to weld on engine mounts (get em from the donor) and there's a fair bit of fiddling iirc
major truma 2
New Member
- Posts
- 525
- Location
- rotherham
interesting.. you fitting with or without turbo?
you'll have to weld on engine mounts (get em from the donor) and there's a fair bit of fiddling iirc
keeping turbo on it ,just gona turn boost right down ,ive got a good supply of s3 gear boxs ready for when ,main or lay shaft snap lol,
engine mounts not too bad ,just add one inch on one side and take a inch of other ,alter bottom right hand side of rad frame so steering arm clears ,,drill two extra hole in bellhouseing for gear box ,, chop inside of passenger wing and fab a flat panel,job done lol
- Posts
- 10,639
- Location
- Oxfordshire
you going to upgrade the brakes? could use the vac pump, also the 300 has the pas pump
major truma 2
New Member
- Posts
- 525
- Location
- rotherham
got 109 brakes on it now ,got a servo assist pedal box too ,,im leaving pas pump on as its easyer to use it as a pulley ,im going to split pump open remove pump impeller and just fill it with grease ,
flat
Well-Known Member
- Posts
- 9,075
- Location
- Far away from you!!
quite a few people run it as a Di, about 90bhp i think.
I think they run it as Di as its an easier fit
I think they run it as Di as its an easier fit
major truma 2
New Member
- Posts
- 525
- Location
- rotherham
it is only easyer with the 200 tdi ,,they remove turbo ,,allso 200 tdi engine mounts are same so no need to make or alter owt ,and no turbo means no intercooler so you can use standard rad
