Hi all, I am new to this page and am looking for some advice. I have a 1980 Series 3 and it came with after market alloys and big old tyres. I want to put it back on it’s original stew wheels and tyres but am getting conflicting advice. What would have been the original wheel size and tyres? Cheers
Series 3 88” Wheels
- Thread starter JNell84
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
steve2286w
Well-Known Member
- Posts
- 4,524
- Location
- monkeyangerland
Welcome , nice Looking series , fun with the top off. I have 750 x 16 Avon rangemasters on mine , quiet on road and handles ok wet and dry
As above the swb would have most likely had 6.00 or 205's tyres originally, however I would fit 7.50's they are what I have on mine. Similarly originally they would have been tubed, but later defender tubless rims look the same and are the same size so it depends on what your preference is. Rangemaster were an original tyre that is more road based, an original all terrain would have been goodyear xtra grip, which you can now get copies off as a deestone extra traction. and a full off road tyre would have been the general super all grip, which from memory someone is remaking but I cannot remember who.
There are lots of others to choose from in a 750 size (I have michelin xzl's) and if you want a metric equivalent although not quite the same size 235/85/16 is the nearest and open up a huge market of different tyres. If you end up with tubed rims make sure they tyre is suitable for tube though.
There are lots of others to choose from in a 750 size (I have michelin xzl's) and if you want a metric equivalent although not quite the same size 235/85/16 is the nearest and open up a huge market of different tyres. If you end up with tubed rims make sure they tyre is suitable for tube though.
steve2286w
Well-Known Member
- Posts
- 4,524
- Location
- monkeyangerland
That’s what I had before the rangemasters , noisy as hell , back end slides were fun , very hard compound , good off road
steve2286w
Well-Known Member
- Posts
- 4,524
- Location
- monkeyangerland
Rims are quite tough are you getting them shot blasted and Anti rust treated
Looks like a petrol but notice the hand throttle holes
Looks like a petrol but notice the hand throttle holes
steve2286w
Well-Known Member
- Posts
- 4,524
- Location
- monkeyangerland
http://www.retroanaconda.com/landrover/category/resources/
this site has some essential stuff for novices and experienced alike
this site has some essential stuff for novices and experienced alike
steve2286w
Well-Known Member
- Posts
- 4,524
- Location
- monkeyangerland
It looks well , if you have all,the pics you could post in members projects section nice to see them getting built back up
Thats what I've got now and can't disagree, they're nearly as noisy as the engine.
steve2286w
Well-Known Member
- Posts
- 4,524
- Location
- monkeyangerland
They do look the part though, 
I had a bloke in pub swearing blind my wheel bearings were gone , wouldn’t have it it was tyre noise
I had a bloke in pub swearing blind my wheel bearings were gone , wouldn’t have it it was tyre noiseThey are positively silent compared to a set of the proper old super all grips, they really do howl.
Bobsticle
De Villes Advocaat
- Posts
- 27,632
- Location
- Manchester
Obvious I know but if you go defender size the speedo will be out a tad.
Mine had big daft balloons on when I got it. Changing them back to a used set of defender steel wheels and tyres was the first job I did.
Mine had big daft balloons on when I got it. Changing them back to a used set of defender steel wheels and tyres was the first job I did.
Hicap phill
Well-Known Member
- Posts
- 16,244
- Location
- Wiltshire
Yep quieter than old SATs
tottot
Well-Known Member
- Posts
- 8,029
- Location
- west wales coast
Avon tyre's produced two types of rangemaster, the 205 had tidy tread pattern that I have to say was the best I have driven on wet grass without ripping it to shreds. the larger 750 size had a different tread pattern.
When I first had SAT's on my RTV trials 88 a four wheel drift to the wrong side of the road informed me of their limited tarmac ability.
Great off road, the best you could get at the time.
When I first had SAT's on my RTV trials 88 a four wheel drift to the wrong side of the road informed me of their limited tarmac ability.
Great off road, the best you could get at the time.
Last edited:
300bhp/ton
Well-Known Member
- Posts
- 5,009
- Location
- Near MK
Remember Series rims are tubed rims, so you need to run tubes. Sadly there are some morons out there who think it is sensible to run without tubes on such rims.
You be careful, you will encourage said idiots to turn up and try and explain why they are not suicidal and illegal and you are wrong.
Do you know what type of rims you have pruchased @JNell84 ? Just because they came from a series does not guarantee they are series rims, defender steels look the same but are tubelss. the part number would tell you and so will the profile of where the bead sits. But if they are tubes not only do you need to fit them with tubes but you also need to fit a tyre that is suitable for running with tubes.
Bobsticle
De Villes Advocaat
- Posts
- 27,632
- Location
- Manchester
I’m going to have to be careful with my brockhouse trailer tyres when the time comes. I think the wheels are series 1 type but looking at the disintegrating remoulds that are on it they might be tubeless. The valves don’t look like they are attached to a tube anyway.
rob1miles
Well-Known Member
- Posts
- 3,565
- Location
- Slough and Bath
I have cross ply tubed trailer tyres on my Sankey - new old stock off e-bay. You can fit tubes on tubess rims, just get fatter valves or the little valve spacers. The crossply tow a lot better because the sidewalls are so stiff they cut down the wandering. I'm sure its an awful ride but no ones in it!
