Is the radiator clean and clear inside? Can you see a temp difference top to bottom? Or is it still cold at the bottom?
Sounding like a water pump or blocked rad to me.
J
Series 2a Wiring
- Thread starter border
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Is the radiator clean and clear inside? Can you see a temp difference top to bottom? Or is it still cold at the bottom?
Sounding like a water pump or blocked rad to me.
J
border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
Radiator is new, there is about 10 degrees difference from top to bottom, ie if top is about 60 then bottom is around 50.
mystery
Well-Known Member
- Posts
- 1,509
- Location
- BULKINGTON
How's the temperature situation going
border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
Sorry just seen this, been busy trying to solve other bloddy niggly problems,
Anyway think its sorted I fitted a new voltage regulator as the one I was using was an old second hand one, tested again idling and needle only went about 3/4 way up, after about 45 mins, give it a run out and needle stays about half way, not going in to the red anymore,
Speaking of test driving Had my first proper try today, only about 4 mile or so.
Must be honest it is a pig to drive,
First time I have drove a Series. Are they all like this ? suppose I will get used to it after a while.
mystery
Well-Known Member
- Posts
- 1,509
- Location
- BULKINGTON
glad you sorted it ,are the temperature readings the same from you gun as before, yes a different way of driving double clutching as no synchro in first and second and the no power steering
I know you can fit power steering one involves destroying the galv on the chassis but there must be a better way, such as anti crush tubes and a clamping configuration .the other is the altering the steering linkages with a expensive kit
i would like to ask a favour could you measure your dip stick from the collar sitting on the tube to the end and the distance from the end of the dip stick to the level mark as mine has been bodged and has several via a hack saw is could be from another vehicle
I know you can fit power steering one involves destroying the galv on the chassis but there must be a better way, such as anti crush tubes and a clamping configuration .the other is the altering the steering linkages with a expensive kit
i would like to ask a favour could you measure your dip stick from the collar sitting on the tube to the end and the distance from the end of the dip stick to the level mark as mine has been bodged and has several via a hack saw is could be from another vehicle
border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
Yes will do that today, not sure where you mean , is it from collar at top of tube to bottom of stick down in the sump ?
mystery
Well-Known Member
- Posts
- 1,509
- Location
- BULKINGTON
yes collar at top of tube to bottom of stick and end of stick to fill mark please
border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
If you need more let me know.
Not sure whats going on here but when I try to upload pics I am getting this message, never happened before. will try again later.
The following error occurred:
You do not have permission to view this page or perform this action.
mystery
Well-Known Member
- Posts
- 1,509
- Location
- BULKINGTON
yes I'm unable to load images it's the site getting the same error message you can use ctrl C (copy) on image you want to use and ctrl V on the site to paste your image
Last edited:
border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
mystery
Well-Known Member
- Posts
- 1,509
- Location
- BULKINGTON
thanks for those
border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
No Problem if you need anymore just let me know.
Thanks m8 printed one out
