Hicap phill
Well-Known Member
- Posts
- 16,238
- Location
- Wiltshire
@Marmaduke you still working off your drive
In the cold?
In the cold?
Scot and Ben
- Thread starter Marmaduke
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
2nd coat of por15...
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
What sort of advert is that 
Hicap phill
Well-Known Member
- Posts
- 16,238
- Location
- Wiltshire
These are like rubber gloves. But are thicker and sensitive
1 size fits all hands & are worn like mittens
Has a little bit sticking out for 1 fingertip to pop out to hold the nuts tight
1 size fits all hands & are worn like mittens
Has a little bit sticking out for 1 fingertip to pop out to hold the nuts tight
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
Two coats of por15
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
Just been and spent over 300 in craddocks on bearings, seals, brakes n drums and nuts n bolts
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
And four tins of this
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
New exhaust arrived today, finally chucking some cash at it
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
Finished exams early and took the advice of @Shimsteriom and partook in a bit of r&r with the angle grinder
After a few measurements and using a length of threaded bar it's time to make the first cut
Removed the old plate that had been bodged on
Then offered the new dumb iron
Plenty of cut off disks in stock
Tomorrow I'll get the welder out and tidy the chassis up and do a better job of replacing the thinner steel and weld the new dumb iron on then do the other side
After a few measurements and using a length of threaded bar it's time to make the first cut
Removed the old plate that had been bodged on
Then offered the new dumb iron
Plenty of cut off disks in stock
Tomorrow I'll get the welder out and tidy the chassis up and do a better job of replacing the thinner steel and weld the new dumb iron on then do the other side
mick the builder
Well-Known Member
- Posts
- 5,901
- Location
- Sligo,Wild West of Ireland.
Why are those discs disintegrating like that? Too much pressure?Finished exams early and took the advice of @Shimsteriom and partook in a bit of r&r with the angle grinder
After a few measurements and using a length of threaded bar it's time to make the first cut
View attachment 201787
Removed the old plate that had been bodged on
View attachment 201789
View attachment 201790
Then offered the new dumb iron View attachment 201791
Plenty of cut off disks in stock
View attachment 201794
Tomorrow I'll get the welder out and tidy the chassis up and do a better job of replacing the thinner steel and weld the new dumb iron on then do the other side
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
Cheap and pinched
mick the builder
Well-Known Member
- Posts
- 5,901
- Location
- Sligo,Wild West of Ireland.
Thought so, look 2nd hand. Talking of h&s, you probably know but using a worn down 9" disc in a 4" grinder is apparently,, different speeds and such.Cheap and pinched
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
Sorry my bad, they're the correct size for the grinder but one of them got pinched between the metal I was cutting. The metal was about 5mm where I was removing the plate
- Posts
- 22,902
- Location
- In the next Glen
Finished exams early and took the advice of @Shimsteriom and partook in a bit of r&r with the angle grinder
After a few measurements and using a length of threaded bar it's time to make the first cut
View attachment 201787
Removed the old plate that had been bodged on
View attachment 201789
View attachment 201790
Then offered the new dumb iron View attachment 201791
Plenty of cut off disks in stock
View attachment 201794
Tomorrow I'll get the welder out and tidy the chassis up and do a better job of replacing the thinner steel and weld the new dumb iron on then do the other side
The state of they discs lol good to see its finally underway.
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
Welder's coming out tomorrowThe state of they discs lol good to see its finally underway.
- Posts
- 22,902
- Location
- In the next Glen
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
Thanks dadAta boy
- Posts
- 22,902
- Location
- In the next Glen
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
'Ere are grandadAta boy
Started hailing just as I was finishing the last side
cos I wanted to get it painted Now it's chucking it down
