Sankey Trailer Redcar cleveland to South West (Bristol)
- Thread starter BearDy89
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 14,902
- Location
- Doncaster
I go to Middlesborough and back on 21st, which is only a few miles from Redcar/Marske.
Can hold the trailer here (bit closer) till further arrangements can be made. I should be going to Wales towards the end of October ...
Don't have a Nato hitch, but do have a 'normal' towball and pin for eye bolt hitch .. Like this, see attachment ..
Can hold the trailer here (bit closer) till further arrangements can be made. I should be going to Wales towards the end of October ...
Don't have a Nato hitch, but do have a 'normal' towball and pin for eye bolt hitch .. Like this, see attachment ..
Attachments
blue beasty
Leaks an prone to bits dropping off
- Posts
- 63,695
- Location
- Gloucestercotshirewolds
Don't think a nato eye will fit behind the pin.......didn't on mine anyway.
I could run it down the M5 from Gloucester/Cheltenham to Bristol if it can be got this far
- Posts
- 14,902
- Location
- Doncaster
Ah, weren't sure so thought I'd mention it!
If OP buys the Nato hitch I'd be happy to bung it on and use that.
- Posts
- 14,902
- Location
- Doncaster
No worries then, get it all arranged for me to collect on 21st this month and pm me the details .. I'll let you know the exact date we're to be in Wales and we can work out a meeting point somewhere ..
- Posts
- 14,902
- Location
- Doncaster
No worries.
Will a Nato hitch have same hole dimensions as a normal tow ball? I suspect not. If anyone has the sizes available, or the seller can measure what the holes are I can drill my drop plate to suit, if necessary.
Will a Nato hitch have same hole dimensions as a normal tow ball? I suspect not. If anyone has the sizes available, or the seller can measure what the holes are I can drill my drop plate to suit, if necessary.
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Nato hitch will need to sit at a different height on a disco though wont it unless your's has been lifted a decent amount and is running big tyres
Pretty sure it has to be anyway but yes same bolts
Pretty sure it has to be anyway but yes same bolts
- Posts
- 14,902
- Location
- Doncaster
Thanks.
Back end sits reasonably high, and I have a receiver and drop hitch that I can use the top holes on .. the trailer's (maybe/probably/hopefully) going to be empty so it's only to move it, not for 'real' use.
Back end sits reasonably high, and I have a receiver and drop hitch that I can use the top holes on .. the trailer's (maybe/probably/hopefully) going to be empty so it's only to move it, not for 'real' use.
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Looks like it could still be a bit low, the nato is mounted through the rear x member on the fenders so might need to fabricate a piece of 5mm steel just to move it up a few inches then bolt through on plate
- Posts
- 14,902
- Location
- Doncaster
Right, so if I can make a plate that makes the Nato hitch bolt to roughly the height of the receiver socket that should be OK? Got loads of 5mm plate .. and some 8mm ..
Not used a Nato trailer before other than a mates a long while ago and can't remember any details other than it was feckin' heavy duty!
Not used a Nato trailer before other than a mates a long while ago and can't remember any details other than it was feckin' heavy duty!
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Yep mate
Basically just need to get it up to the height it would be on a military fender so probably about rear bumper on your disco I'd say, then you need to either pull the pin on the nato or pull the pin on the trailer depending on which one is static and which is selectable. Never have both moving though!
I'd suggest using the 8mm just to be safe
Basically just need to get it up to the height it would be on a military fender so probably about rear bumper on your disco I'd say, then you need to either pull the pin on the nato or pull the pin on the trailer depending on which one is static and which is selectable. Never have both moving though!
I'd suggest using the 8mm just to be safe
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
That looks about the right height
tyre man dave
Active Member
- Posts
- 734
- Location
- redcar cleveland
hi guys p213nab disco is this what you using to collect trailer.?
CAN LOAN DIXON BATE FIXINGS, Should bolt onto your pack plate .then you have height make it easy to tow better .WOULD NEED IT BACK FOR 110.
CAN LOAN DIXON BATE FIXINGS, Should bolt onto your pack plate .then you have height make it easy to tow better .WOULD NEED IT BACK FOR 110.
tyre man dave
Active Member
- Posts
- 734
- Location
- redcar cleveland
Hi paul.
What size box section is your tow eye
may be able to sort something out in fab shop at work ?
What size box section is your tow eye
may be able to sort something out in fab shop at work ?
- Posts
- 14,902
- Location
- Doncaster
Yep .. it's OK, I think my normal towplate turned upside down will work fine, thanks. So long as you're happy for me to collect on the 21st. Can't say a time yet 'cos we have to drop son off at Uni, and he has to pick his keys up and transfer his belongings into digs .. dunno how long it'll take. Last year it took ages ...
Similar threads
