Rubber/seal that goes between the bulkhead and the lower dash

fmrodrigues · Jul 15, 2013

Hello,

This is my first time at the forum.

My name is Frederico and Im from Portugal.

Im trying to find the part number from the rubber/seal that goes between the bulkhead and the lower dash (duct heater).

Im posting a photo I found at the web with the rubber/seal Im looking for.

Thanks in advanced.

Regards

Frederico

Pikey · Jul 15, 2013

Hi Frederico and welcome to LZ.

the part number you want is LR016690

Pikey · Jul 15, 2013

Whoops never read that properly :doh:

fmrodrigues · Jul 16, 2013

No problem.

Frederico

gse1986 · Jul 16, 2013

That's wrong part number isnt it? Isn't he wanting the rubber that goes on the bulkhead?

fmrodrigues · Jul 16, 2013

If fact it is.

The part Im looking for is the one Ive marked in yellow.

The problem is, I cant find it at the parts catalogue.

Regards

Frederico

timtheenchanteruk · Jul 16, 2013

http://www.landroverworkshop.com/diagrams/

should be in here somwhere, having a look now, but not seen it yet.

fmrodrigues · Jul 16, 2013

Thats the one million dollars question

The Portuguese Land Rover parts seller cant find it either.

Regards

Frederico

timtheenchanteruk · Jul 16, 2013

does it even have a seal, or is it sealed with mastic??

gse1986 · Jul 16, 2013

the rubber is on td5 bulkheads, I havent taken my 200tdi one apart yet. On td5 one it was rivetted onto the bulkhead. If its on the 200tdi, I'll probably be needing a new one as I wrecked the td5 one as I took it apart

bluehaze · Jul 16, 2013

That's my landy

fmrodrigues · Jul 16, 2013

Timtheenchanteruk,
Its a simply hard rubber, but in my case, I think because of the heat, its completely damaged and following into peaces!
Bluehaze,
Sorry for using your photo without the right credits!
Where did you get the seal/rubber Im looking for?

Frederico

bluehaze · Jul 17, 2013

Can't be 100% sure - it was either on the bulkhead when I bought it (most likely), came with the dash or supplied by LRSeries (I used them for the rebuild).

If you can't find one fit some insulation over the area.

Use all the photos you like - I have lots that are not released yet.

Dippypud · Jul 17, 2013

Pushbike inner tube split and laid flat, (valve cut out )...

fmrodrigues · Jul 17, 2013

[FONT=&quot]After the help from Nick from Dunsfold the part number should be ETD102970, in this case for a LHD TD5, for the RHD TD5 it should be ETD102960.[/FONT]
[FONT=&quot]
[/FONT]
[FONT=&quot]Unfortunately the parts catalogue has no pictures of it and they are no longer available from Land Rover.[/FONT]
[FONT=&quot]
[/FONT]
[FONT=&quot]Many thanks for all the help.[/FONT]
[FONT=&quot]
[/FONT]
[FONT=&quot]Regards[/FONT]
[FONT=&quot]
[/FONT]
[FONT=&quot]Frederico [/FONT]

timtheenchanteruk · Jul 17, 2013

£160.00 ,not surprised....

fmrodrigues · Jul 17, 2013

[FONT=&quot]In fact I think it was way too much for it[/FONT]
[FONT=&quot]
[/FONT]
[FONT=&quot]Maybe its made from a super special rubber![/FONT]
[FONT=&quot]
[/FONT]
[FONT=&quot]Frederico[/FONT]

gse1986 · Jul 17, 2013

Bit annoyed mines in pieces now!

bluehaze · Jul 17, 2013

It's very similar to the material used in the Haz kits. Except that the Haz has a aluminium cover on one side. Buy the kit, open up the green covers and cut the insulation to fit your needs.

Rubber/seal that goes between the bulkhead and the lower dash

New Member

Attachments

Dummy Ejection Facilitator..

Dummy Ejection Facilitator..

New Member

Active Member

New Member

Well-Known Member

New Member

Well-Known Member

Active Member

Well-Known Member

New Member

Well-Known Member

Never Knowingly Understood

New Member

Well-Known Member

New Member

Active Member

Well-Known Member

Similar threads