Reverse Light cable

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
CassienLandy

CassienLandy

Member
Posts
24
Location
Dartford
I have a 1994 300tdi and the cable is missing from the loom to the switch on the gearbox. There is a two pin plug on the switch end and there is a spare? two pin plug in the engine bay on the loom. I assume there is a link lead to go between the two? Does anyone know what this is called? I can't seem to find it on a parts search anywhere. Perhaps I am using the wrong wording.
 
CassienLandy said:
I have a 1994 300tdi and the cable is missing from the loom to the switch on the gearbox. There is a two pin plug on the switch end and there is a spare? two pin plug in the engine bay on the loom. I assume there is a link lead to go between the two? Does anyone know what this is called? I can't seem to find it on a parts search anywhere. Perhaps I am using the wrong wording.
Click to expand...

I don’t know about a “link cable” for it, but it’s such a simple circuit that you could make your own. The switch usually has an ignition switched live to it, closes when reverse is selected, and powers the reverse light(s). If you take photos of the connectors you have, someone like @PaulMc should be able to supply the connectors you need. Before you go connecting anything, make sure you know what that “spare 2 pin plug” is for.
 
Thanks for the reply, the plan is to link out the connector at the loom and see if the reverse light comes on. If that fails I am going to have to wire it myself. Obviously this is simple electrically just a bit of a bitch to get to, would be really easy with a £5 lead.
 
CassienLandy said:
Thanks for the reply, the plan is to link out the connector at the loom and see if the reverse light comes on. If that fails I am going to have to wire it myself. Obviously this is simple electrically just a bit of a bitch to get to, would be really easy with a £5 lead.
Click to expand...

Is it a defender?
 
CassienLandy said:
Yes mate, a Defender. The plug in the engine bay is not the reverse light. Going to run a new circuit.
Click to expand...

Take the centre seat or cubby box out, and the centre cover plate. The reverse switch should be easily visible. On mine, the wiring comes out of the loom, just under the drivers seat, so maybe yours is tucked up somewhere?
 
I have checked just about everywhere, I don't understand it. The only cables that exit the loom in that area are the pair for the dash tell on four wheel drive.
 
CassienLandy said:
I have checked just about everywhere, I don't understand it. The only cables that exit the loom in that area are the pair for the dash tell on four wheel drive.
Click to expand...

Im sure it should only be one for the difflock telltale. It shorts to earth through the switch, so doesn’t need a return back to the loom.

Has someone messed around the loom and your trying to get it back to a decent condition?
 
The vehicle has had lots of bits and bobs over the years, I put a galvanised chassis on it 2 years ago. I am guessing the reverse light was never reconnected. I am pretty sure there are no other loose ends. Ran a new circuit today, works fine. Just took a fused live through the switch and to the light, made the loose ends in the light safe, all good.
Just read your comment again, shorts to earth in the switch? Surely it wouldn't work the way I have wired it then? I should have blown a fuse?
 
CassienLandy said:
The vehicle has had lots of bits and bobs over the years, I put a galvanised chassis on it 2 years ago. I am guessing the reverse light was never reconnected. I am pretty sure there are no other loose ends. Ran a new circuit today, works fine. Just took a fused live through the switch and to the light, made the loose ends in the light safe, all good.
Just read your comment again, shorts to earth in the switch? Surely it wouldn't work the way I have wired it then? I should have blown a fuse?
Click to expand...

The transfer box shorts to earth, so doesn’t require 2 wires. It was in response to a post you said “2 wires going to the transfer box”. The reverse light switch should be wired as you have done, live in, switched out.
 
There are two wires at the transfer box, neither connected. when I linked between the two to see what happened the diff lock tell came on.
 
CassienLandy said:
There are two wires at the transfer box, neither connected. when I linked between the two to see what happened the diff lock tell came on.
Click to expand...

That’s interesting. I was under the impression they were all wired the same, so a live from the loom, to one side of the switch, the other side of the switch is connected directly to the bolt head of one of the cover bolts. So when the difflock switch closes, it effectively shorts to earth and illuminates the light.
 
I just linked both together and the diff lock light came on. Haven't seen where they connect to the transfer box, its not the original box anyways.
 
CassienLandy said:
I just linked both together and the diff lock light came on. Haven't seen where they connect to the transfer box, its not the original box anyways.
Click to expand...

If the transfer box is LT230, then it should be just under high low linkage. You can see it from removing the centre seat cover. Here is a diagram showing it as if your looking from the RHS of the vehicle.

upload_2020-10-10_8-42-39.jpeg
 
You must log in or register to reply here.

Similar threads

S
wiper park switch: why does it connect to earth
Replies
8
Views
324
mystery
mystery
G
Reverse light
Replies
11
Views
721
TrevD
T
I
6-pin cable connector next to BCU
Replies
3
Views
426
invisible999
I
StuRox
Disco 1 Interior Light door switch wiring
Replies
8
Views
349
StuRox
StuRox
T
Reverse light switch
Replies
6
Views
769
tottot
tottot
Back
Top