Replacing rear 1/4 chassis rear cross member series 3 88”

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
L

Landyfella

Active Member
Posts
162
Location
Cambridge
Hi all, I am new to the Land Rover, but have restored 5 previous cars so have general experience. I am replacing the rear end and would just like to check to see if there are any gotcha’s or advice about doing it.

Obviously I am putting the car on stands and releasing the leaf springs. The tub is off but when I cut of the rear end will put tub back on so it all lines up correctly then tacking it.

The crossmember is from bearmach and sleeves part of the old chassis. Cut off is just in front of the first rear tub mount seat.
I know about the wiring harness running through in the drivers side
Thanks
Chris
 
No problem. There's a lot to be said for re-routing the harness too make it easier to inspect and add wires. And really really get the alighment right, don't rely on the tub. I've met someone whose rear chassis was welded on out of line, very hard to fix.
 
I did it by leaving the tub in situ until it was tacked in. Couldn’t trust myself to get it back on in the right place. :oops:
 
My Dad likes to regale me with the tale of when he did his rear quarter over a weekend between work and left the tub in place. They took the tub floor up for access. I'd probably have the tub off myself as I'm not as experienced and would prefer to make a jig and have all the access I wanted.
@rob1miles My harness is still in there and it was a worry when I did the outriggers that side and it's more of a worry for the welding I've got to do above the rear bump stops.. where's a good place to re-route it to?
 
I got a lenght of multi-core cable - 9 I think but you may find trailer cable with 7 is enough. I wanted a couple of extras. I cut the loom out where it goes into the chassis near the bulkhead and where it comes out near the rear wheel and put in connection blocks - one behind the dash and one by the rear lights then swaped it over. Cable runs along the top of the chassis. Came in really handy when I added a tow socket as all the wires were in one place.
 
I used ordinary garden hose as trunking and fed through it, the correct coloured wires which I got from Autosparks. The hose, I fed over the transverse floor supports where they jump over (under) the longitudinal floor supports, it is out of the way and looks neat, you can push it though a grommeted hole into the tool boxes and hook up the wires to the lights.
You can see the gap where the cross bars meet the length-wise bars, perfect place; this pic taken before the wiring was installed.
Under rear 2.resized.JPG
 
Last edited:
Extreedoc said:
I used ordinary garden hose as trunking and fed through it, the correct coloured wires which I got from Autosparks. The hose, I fed over the transverse floor supports where they jump over the longitudinal floor supports, it is out of the way and looks neat, you can push it though a grommeted hole into the tool boxes and hook up the wires to the lights.
You can see the gap where the cross bars meet the length-wise bars, perfect place; this pic taken before the wiring was installed.
View attachment 219000
Click to expand...
Mines posher than that. It has a fitted brown carpet to hide all the mecul.
 
You must log in or register to reply here.

Similar threads

dag019
Station wagon conversion
Replies
11
Views
968
shaynecm
S
dag019
Fitting YRM extended second row floor upstand
Replies
14
Views
619
dag019
dag019
jimllshiftit
Any advice for novice welder about to stitch new rear cross member to 90 chassis?
Replies
3
Views
789
tottot
tottot
T
Series 1 ID
Replies
4
Views
971
Bobsticle
Bobsticle
D
Series 3 chassis lug bracket
Replies
4
Views
989
Wildefalcon
W
Back
Top