Landshandy
Active Member
- Posts
- 653
I have a d2 facelift and was wondering where to put recovery points on?
Disco 2 Recovery Points D2 facelift
- Thread starter Landshandy
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Landshandy
Active Member
- Posts
- 653
Or maybe this is a impossible task from what I've read?
neilly
Well-Known Member
- Posts
- 20,000
- Location
- Oxfordshireness
You can get some steering guards with recovery points fitted. not sure what you would need to modify bumper wise.
neilly
Well-Known Member
- Posts
- 20,000
- Location
- Oxfordshireness
As an example.
http://www.lrparts.net/three-piece-steering-guard-with-shackles-for-discovery-2.html
Cheers
http://www.lrparts.net/three-piece-steering-guard-with-shackles-for-discovery-2.html
Cheers
Landshandy
Active Member
- Posts
- 653
I've just spent £168 on a mantec aluminium steering guard
I have a nudge bar attached to the front? Doubt that will hold will it?
Landshandy
Active Member
- Posts
- 653
neilly
Well-Known Member
- Posts
- 20,000
- Location
- Oxfordshireness
Have found this. Not sure if it is still available or possible in the time scale you have.
http://blog.discoverthat.co.uk/2010/02/land-rover-discovery-td5-front-recovery.html
Cheers
http://blog.discoverthat.co.uk/2010/02/land-rover-discovery-td5-front-recovery.html
Cheers
Landshandy
Active Member
- Posts
- 653
Cheers Neilly, I can give it a go. As back up I've bought a tow bar so I can use that. I've seem loads of photos of something like the picture below but only in the US
Landshandy
Active Member
- Posts
- 653
Part for the rear is db1322
300bhp/ton
Well-Known Member
- Posts
- 5,009
- Location
- Near MK
What do you plan to do with the D2? As in terms of use?
Recovery points should be GOOD and suitable. Poor recovery points are just dangerous and an accident waiting to happen.
Make sure you use high tensile bolts (8.8 or higher) and will likely need a retaining plate if you are bolting it through. Also make sure whatever you bolt to is sufficiently strong enough and attached to the vehicle securely. i.e. if you attach a recovery point to a bumper, the bumper also needs to then be attached with high tensile bolts.
Recovery points should be GOOD and suitable. Poor recovery points are just dangerous and an accident waiting to happen.
Make sure you use high tensile bolts (8.8 or higher) and will likely need a retaining plate if you are bolting it through. Also make sure whatever you bolt to is sufficiently strong enough and attached to the vehicle securely. i.e. if you attach a recovery point to a bumper, the bumper also needs to then be attached with high tensile bolts.
Landshandy
Active Member
- Posts
- 653
I'm off to Morocco for 4-5 weeks, I've bought a tow bar and want to attach it to the rear. Not many options for the front
Landshandy
Active Member
- Posts
- 653
Could I just use the tow bar fixture?
Landshandy
Active Member
- Posts
- 653
Does anyone know of a shackle that will fit the m16 holes on the OEM tow bar?
Only ones I can find are for NATO holes
Only ones I can find are for NATO holes
Landshandy
Active Member
- Posts
- 653
Could I not use this? http://www.britpart.com/part/db1329
discool
Well-Known Member
- Posts
- 13,609
Nope, they are meant to be installed directly to the chassis.
U said you wanted a shackle so there are loads on eBay, so take your measurements then take your pick.
Link as an example.
http://www.ebay.co.uk/itm/5mm-6mm-8...hash=item5d5082372a:m:mG_LJFDSngitI9O_8KhvGFA
U said you wanted a shackle so there are loads on eBay, so take your measurements then take your pick.
Link as an example.
http://www.ebay.co.uk/itm/5mm-6mm-8...hash=item5d5082372a:m:mG_LJFDSngitI9O_8KhvGFA
brian47
Well-Known Member
- Posts
- 8,867
I'm no expedition or recovery expert, and I will defer to those who do know better, but the device you've shown is a Jate Ring, rather than a shackle.
As @discool has already said, Jate rings can be used as recovery points, but only in properly prepared chassis mountings; the holes aren't just drilled through the chassis but they're then lined and the lining welded in place, just like the mounting points in the chassis for fitting a towbar.
Correct size and specification Jate rings can be installed, but from what I've been able to find, instead of a towbar and therefore using the existing mounting points on the chassis.
Front HD recovery points on a Disco present you with a couple of problems, the main one being that the plastic bumper assembly extends lower than the chassis and so it would foul any towing equipment which would probably cause a not insignificant amount of frontal damage. If you've fitted a winch bumper then your problems are then ones of finding a correct place to install the jate rings.
I've added a couple of pics to illustrate:
As @discool has already said, Jate rings can be used as recovery points, but only in properly prepared chassis mountings; the holes aren't just drilled through the chassis but they're then lined and the lining welded in place, just like the mounting points in the chassis for fitting a towbar.
Correct size and specification Jate rings can be installed, but from what I've been able to find, instead of a towbar and therefore using the existing mounting points on the chassis.
Front HD recovery points on a Disco present you with a couple of problems, the main one being that the plastic bumper assembly extends lower than the chassis and so it would foul any towing equipment which would probably cause a not insignificant amount of frontal damage. If you've fitted a winch bumper then your problems are then ones of finding a correct place to install the jate rings.
I've added a couple of pics to illustrate:
Landshandy
Active Member
- Posts
- 653
What do I attach said shackles to?
discool
Well-Known Member
- Posts
- 13,609
Well U said "tow bar" why lot get a "pin ball" wizard tow hitch and fit to the tow bar.
