rear mount tie bar/ engine mount

krisjones91 · Oct 29, 2014

can anyone here please tell me if they have replaced the rear engine mount tie bar?, and what they did to do so please.
it looks simple enough to look at, as in its only two bolts?
is it a simple case of removing sump cover, taking the engine weight on a jack and then swapping the parts over.
thanks for any help.

GrumpyGel · Oct 29, 2014

TBH I don't think you need to support the engine as its only a damper affair - the top mounts support the weight of the engine. It just has a bolt on the subframe and another on the IRD bracket. It should come off quite easily if I remember right.

teddywood1 · Oct 29, 2014

I have done it on my old one but I am sure it is more than 2 bolts possibly it could be three get a jack under it with a piece of wood between the jack and sump as the top engine mounts will give a bit I remember using a crow bar to pull the engine into place.

Nodge68 · Oct 29, 2014

Easy job. 2 bolts to remove. No need to jack the engine as weight is taken by the end mounts. Replace with polyurethane for longer life

Irishrover · Oct 29, 2014

Nodge68 said:
Easy job. 2 bolts to remove. No need to jack the engine as weight is taken by the end mounts. Replace with polyurethane for longer life

:behindsofa:

Is the steady the same on all versions of the F/L ??
Any idea where the polybuses can be obtained from?

Cheers

teddywood1 · Oct 29, 2014

I remember why I had the jack is because I had the top mount off as well I was doing the bottom pulley.

Nodge68 · Oct 29, 2014

Irishrover said:
:behindsofa:

Is the steady the same on all versions of the F/L ??
Any idea where the polybuses can be obtained from?

Cheers

Yep all the same iirc.
You can use the polyurethane upgraded version from a rover 200 too

Like this, although the price has risen some what!! http://www.ebay.co.uk/itm/ROVER-220...arts_Vehicles_CarParts_SM&hash=item4ab3825c26

Sucram · Oct 29, 2014

That poly bush price can't be right at £289 that's ridiculous.

krisjones91 · Oct 30, 2014

thanks for the reply. il look into it and change the mounts on the weekend when im back home. my only other question is since i took the prop off it showed how weak the rear mount was so the engine was swaying. but also the hydro mount area is creaking like hell since. is it hard to replace that mount as well. im hoping the rear mount is gonna stop the noise but the hydramount seems cheap enough but looks like a hard job. cheers

Kizzeh · Oct 30, 2014

Sucram said:
That poly bush price can't be right at £289 that's ridiculous.

£289 plus vat!
I need one but I'll think I'll pass at that price

Diesel Do · Oct 30, 2014

Loads on eBay £35-40
I got some from euro car parts not that long ago

Nodge68 · Oct 30, 2014

Sucram said:
That poly bush price can't be right at £289 that's ridiculous.

I think it's a price error. These are normally around £30.
Here you go.
MG ZS Powerflex Engine Mount Stabilisers (Large) PFF63-418 | eBay

Sucram · Oct 30, 2014

Nodge68

Thanks for putting that link up for the powerflex bush, at 30 quid that's more like it

Nodge68 · Oct 30, 2014

Sucram said:
Nodge68

Thanks for putting that link up for the powerflex bush, at 30 quid that's more like it

You're welcome

I had two of those in my V6. One on the lower tie bar, the other on the upper tie bar.
It makes a massive difference to the location of the power unit. Feels better under braking too.

Northern Irelander · Oct 31, 2014

I just made my own rubber bush, still going strong after 8yrs

rear mount tie bar/ engine mount

krisjones91

New Member

GrumpyGel

Well-Known Member

teddywood1

Well-Known Member

Nodge68

Well-Known Member

Irishrover

Well-Known Member

teddywood1

Well-Known Member

Nodge68

Well-Known Member

Sucram

Active Member

krisjones91

New Member

Kizzeh

Well-Known Member

Diesel Do

Well-Known Member

Nodge68

Well-Known Member

Sucram

Active Member

Nodge68

Well-Known Member

Northern Irelander

Well-Known Member

Similar threads