Looking for a pair of axle stands and have seen 3 tonne Ratchet Axle Stands at Halfords for £30 and at B&Q for £21. Has anyone used such an item not sure if I would feel safe using them rather than a conventional stand with a load pin? Any views welcome, cheers John
Ratchet Axle Stands
- Thread starter Connorefc
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 1,855
- Location
- Selby, North Yorkshire
We've used a pair in the garage for the last two years to work under London type taxis. No problems.
chris7
Well-Known Member
- Posts
- 1,310
- Location
- Spalding, Lincolnshire
Hmmmm I think I'm in doubt like you John and would rather trust a pair with load pins! Halfords sell them 2 or 3 tonne load available regards. Chris
Yoyodyne
Well-Known Member
- Posts
- 1,977
- Location
- West Yorkshire
Used them for years - never had a problem. Found them quicker and easier to use than trying to get a pin in a hole!
West Slope Rover
Well-Known Member
- Posts
- 8,617
- Location
- deep underground
I have 4 of them and use them all the time on my RRC LSE. They've not squashed me yet.
v8geoff
Well-Known Member
- Posts
- 3,327
- Location
- chippenham,wiltshire
Brilliant piece of kit
bluedog333
Well-Known Member
- Posts
- 5,442
- Location
- Henley on Thames, Oxfordshire
They work! Don't think of the ratchet mechanism in a socket wrench, as this will lead you to thinking they are not man enough to hold a Landy! If you are paranoid, you can buy stands with a pin as well, Faithfull Tools make (supply) some.
payydg
Well-Known Member
- Posts
- 3,907
- Location
- Aberdeenshire
I've used them and they're totally fine
Yoyodyne
Well-Known Member
- Posts
- 1,977
- Location
- West Yorkshire
They wouldn't/couldn't sell them if they didn't work. There would be a bit of bother if folks were getting flattened all over the country. But it seems like you've made your mind up ...
Yet !
waldershelf
Well-Known Member
- Posts
- 2,397
- Location
- In the hills north west of Sheffield
I have four 3 tonners that I use all the time, hey are more than up to the job. The ratchet mechanism is no more likely to fail than any other stand design.
- Posts
- 3,275
- Location
- Rushden, Northants, UK
We have 8 X 3 tonne and 4 X 2tonne, use them all the time, never had an issue in 8 years or so.
Peter
Peter
No I hadn't that is why I posted the question, I don't know anyone who has any so thought best ask for opinions.
neilly
Well-Known Member
- Posts
- 20,000
- Location
- Oxfordshireness
just watch your fingers when you disengage the ratchet when you are setting them to thier lowest position before you put them under the motor. got a nice blood blister from seeing how they worked and then them dropping on my finger, LOL
- Posts
- 7,877
- Location
- East Midlands
Yes, mine catch me just on the web between thumb and index finger as I drop them. That seems to be the major danger. The advantage is that they go up and down in smaller steps than the pin versions and you can therefore make better use of your jack's travel. I was a bit apprehensive at first, having only had the pin ones before, but I'm still in one piece and haven't been laminated to the tarmac yet.
- Posts
- 44,864
- Location
- Hornchurch
They'll be fine
Chockydogs
Active Member
- Posts
- 133
- Location
- Leicester
Just to add, I bought a pair of 3 ton ones from Toolstation, there fine for under the axles as they arnt very tall, ended up getting a pair of 6 tom stands from machine mart for about £38 - bit more expensive but I have them on the chassis of my S3 at the moment with the rear axle off.
Depends what you want them for, but I didnt want to put my little axle stands on concrete blocks to make them high enough (well not for long anyway!)
r
Similar threads
