R380 drain plug

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
D

Danceable

New Member
Posts
27
Hello all,

Still busy trying to fix oil leaks (engine and transfer box) on my late 2005 TD5 Landmark before going to France at the weekend. Whilst laying under the beast today trying to spot the source of the multitude of leaks I thought I'd change the gearbox oil as I have some MTF95 in the shed. Problem is, however hard I tried, I cannot get the sump plug off. Either the oil has not been drained in the last 136K miles or when Land Rover last did it they decided to do it up tight!

Cannot get a socket onto it (although I may be able to soon as the transfer box has to come out as one of the big oil leaks is from the intermediate shaft O ring seal at the front end). Can anybody tell me what size the drain plug/nut is please as I will go and borrow a spanner to fit rather than a big adjustable that I have tried to use today!

BTW, I cannot help but feel that the 5W30 that I have put in to the engine has increased the amount of leaks as I am assuming it had 10W40 in it beforehand. Anybody had similar issues?

Many thanks, Julian
 
On the r380 I think it'll be 32mm, if its the same as the d1 box.

One trick I used on my d1 was to use a massive draper pro spanner with trolly jack pushing it tight. You'll probably find that the drain plug will take the weight of the whole vehicle without undoing. Use a heatgun or small blowtorch to warm the casing up. It will shift, be careful with heat/fire obviously. And watch the vehicle doesn't 'drop' if the spanner is taking weight when the thread brakes.

Edit - make sure you can get the fill plug out first!
 
Hi all,

Thanks for replies. Tried the jacking up method today but just managed to jack the entire vehicle up!! It's on real tight. Will try some heat tomorrow, but thanks for the size - I used calipers on my adjustable and came up with 32mm, but always good to confirm. It's not helped by the fact that somebody has already had a 'real go' at the nut so having to be careful to avoid rounding off.

Why so tight!!!
 
Yeah if all else fails give it a smack and set it on fire :)

If you use flame make sure the box is dry heh, flash fires 2 inch from your face ain't good!
 
Mine is a 3/8 square and just as tight. I have just destroyed a 3/8 square drive ratchet (it was a cheap one). I have got to come up with a stronger better method.
 
If it's the earlier type, i.e. the 32mm hex head, there's also a washer in there (part FTC4112). Most (myself included) forget about this until it's too late and since it's not the kind of washer that most DIY mechanics will have lying around, it will end up reused and the bolt over tightened to compensate. If it's the newer type of plug, then it will most likely have thread locker on it. Heat will help, even if you had to take the vehicle for a good spin, which would also warm up the oil to help with draining. Just remember to let the metal cool down before you apply the tightening torque.
 
Trouble is it is only 3/8 square and they are not very strong. I have just bought a 1/2 to 3/8 square drive adaptor and will try that on a breaker bar tomorrow. I wanted an impact one as that would be stronger but Toolstation hadn't got one in stock.
 
iu

Just sneak up on it ...
 
You must log in or register to reply here.

Similar threads

E
Disco 2 Fuel Leak
Replies
1
Views
137
Landmark2
Landmark2
Dieselweasel0
Discovery lt77 gearbox
Replies
5
Views
384
lynall
L
M
Drove through 2 feet of water, next day, clunking/sputtering when turning left/right slowly?
2 3
Replies
46
Views
2K
mantrid
M
mad85
Disco 2 plug and play ECU?
Replies
3
Views
632
sierrafery
sierrafery
S
Hi/low switch
Replies
8
Views
468
Shore968
S
Back
Top