Steve Noakes
Active Member
- Posts
- 131
- Location
- Sussex
Project No. 2 - 1969 series 2A 88inch
- Thread starter Steve Noakes
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Tim_AM
Well-Known Member
- Posts
- 113
- Location
- Sydney, Australia
Nice find! Looks like you might have your work cut out!
What are your plans for it?
What are your plans for it?
Steve Noakes
Active Member
- Posts
- 131
- Location
- Sussex
Thanks, my aim is to put it back to as close as original as possible, not concourse but authentic. spent a few hours looking over it, it will keep me busy for a while but that was the plan.
It's had 14 owners according to log book so has seen a number of mods over the years which will take some time to get the right list of original specs.
The instrument layout is proving tricky, any clarity on a Feb. 1969 IIA layout would be appreciated. So far I think the spec should be : left display is coolant temp + Fuel gauge but not clear what should be in the lower segment. Speeds should be 70mph with 3 lights in lower segment. Choke in lower right corner of instrument panel. Can't determine whether there are warring lamps in the panel as well as in the dials. Mine has a separate oil pressure gauge on a separate panel plate. Was this ever a IIA option or an add on ?
It's had 14 owners according to log book so has seen a number of mods over the years which will take some time to get the right list of original specs.
The instrument layout is proving tricky, any clarity on a Feb. 1969 IIA layout would be appreciated. So far I think the spec should be : left display is coolant temp + Fuel gauge but not clear what should be in the lower segment. Speeds should be 70mph with 3 lights in lower segment. Choke in lower right corner of instrument panel. Can't determine whether there are warring lamps in the panel as well as in the dials. Mine has a separate oil pressure gauge on a separate panel plate. Was this ever a IIA option or an add on ?
Marmaduke
Well-Known Member
- Posts
- 9,773
- Location
- Near the land of 'Me Duck'
It's got military wings on it which is why the side light and indicator are above each other as opposed to side by side
Steve Noakes
Active Member
- Posts
- 131
- Location
- Sussex
Thanks Marmaduke, I thought they military as I've seen images like that. I have a spare set of wings which came with it and these are the non-military versions but not in great condition. Maybe look for a set of wings at Landrover fest.
Steve Noakes
Active Member
- Posts
- 131
- Location
- Sussex
I'm also looking for a dynamo pulley and fan as the dynamo which was in the tub has a wide belt groove which doesn't match the 2 pulleys on the engine. I believe the correct pulley should be A-section ?? Was the wide pulley from a military too ?
Steve Noakes
Active Member
- Posts
- 131
- Location
- Sussex
Spent some time to get her started. Needed to replace the fuel lift pump and coil and then it started first time.
My son had a go as well which was great fun. Now the real work begins for the refurb.
small video on youtube ...
My son had a go as well which was great fun. Now the real work begins for the refurb.
small video on youtube ...
Steve Noakes
Active Member
- Posts
- 131
- Location
- Sussex
The engine has twin belt pulleys and an oil coiler in front of the radiator. Were these fitted to civilian spec vehicles ?
Steve Noakes
Active Member
- Posts
- 131
- Location
- Sussex
Spent a few pleasurable hours stripping it down to expose the chassis. No unpleasant surprises so happy with the scale of work to do.
Steve Noakes
Active Member
- Posts
- 131
- Location
- Sussex
The Dumb Iron and out rigger need to be replaced. The rear cross member has been patched up too many times so will be replaced with a new quarter chassis section.
Steve Noakes
Active Member
- Posts
- 131
- Location
- Sussex
Spent a nice weekend with Dad cutting out the rotten chassis members and tacking in new ironware. A great welder from work, Dan, gave up an evening after work to weld the metalwork. A great job resulting from a guy who knows how to weld... Stick welded using a 5.5kVA Machine Mart generator. It coped very well at over 100A weld setting.
Outrigger cut out and replaced
New dumb iron welded up
rear 1/4 replaced, great welding
finally moved the chassis to a closed order of the barn, build a simple store to keep bits tidy
Dinner Al Fresco under the barn....Thanks Dad for the great help, Thanks Mum for the copious tea and bacon sandwiches and thanks to Mum and my good lady wife for letting the boys play together.
Outrigger cut out and replaced New dumb iron welded up rear 1/4 replaced, great welding finally moved the chassis to a closed order of the barn, build a simple store to keep bits tidy Dinner Al Fresco under the barn....Thanks Dad for the great help, Thanks Mum for the copious tea and bacon sandwiches and thanks to Mum and my good lady wife for letting the boys play together.Attachments
Last edited:
Steve Noakes
Active Member
- Posts
- 131
- Location
- Sussex
Steve Noakes
Active Member
- Posts
- 131
- Location
- Sussex
With the welding complete, the running gear was removed and stripped ready for sand blasting. Springs seem ok to refurbish, shock are well rusted and leaking so new ones on order.
The big day for chassis sand blasting finally came. We moved the chassis into the field to save filling the barn with sand. A few hours later and the chassis and axles were cleaned and ready for further inspection.
I'm using POR 15 chassis preparation so after sand blasting, the chassis and axles got a good coating of Metal Prep and then washed off as per instructions. Only a few parts of the chassis and bulkhead need some extra work so I'll give the good areas the 2 coats of POR 15 anti-rust and leave the few places untouched ready for local repairs.
The big day for chassis sand blasting finally came. We moved the chassis into the field to save filling the barn with sand. A few hours later and the chassis and axles were cleaned and ready for further inspection.
I'm using POR 15 chassis preparation so after sand blasting, the chassis and axles got a good coating of Metal Prep and then washed off as per instructions. Only a few parts of the chassis and bulkhead need some extra work so I'll give the good areas the 2 coats of POR 15 anti-rust and leave the few places untouched ready for local repairs.
Last edited:
Steve Noakes
Active Member
- Posts
- 131
- Location
- Sussex
The good parts of the chassis have had the POR15 chassis black paint. Looks much better. Bulkhead A pillars are as expected when first seen, 1 will be replaced fully and 1 looks repairable.
flat
Well-Known Member
- Posts
- 9,075
- Location
- Far away from you!!
wow this is a great project, following 
Steve Noakes
Active Member
- Posts
- 131
- Location
- Sussex
The project had to take a rest for 6 months due to work commitments. Got back to it and have made some good progress.
Work completed so far :
Work completed so far :
- Engine rebuild - valve guides replaced with later type as I couldn't get good fitting o-rings. Engine was in remarkably good condition inside.
- New water pump, hoses etc.
- New engine and transmission mounts
- Front and rear diffs stripped and rebuilt with new shims to set correct mesh engagement etc.
- New front driveshafts as 1 was significantly twisted on the spline
- New swivel balls, seals and bearings replaced in axles
- New Propshaft UJs as signs of wear evident
- Brakes fully replaced with new cylinders, shoes, and pipes throughout
- Leaf springs stripped, de-rusted, painted and re-built with new shackle rubbers. New shackle plates throughout as they all had major wear marks
- New shock absorbers front and rear
- Transmission checked and some seals and bearings replaced. No sign of wear or damage evident.
- Transmission (park) brake overhauled with new cylinder, shoes, adjuster rod
- New exhaust throughout
- Dynamo overhauled, new brushes, cleaned, painted and new twin pulley installed
- Round heater matrix purchased and overhauled to be installed in final assembly
- Bulkhead repairs complete with new A-pillar, multiple bad quality and redundant holes welded up. Painted in final colour before engine installed
- Doors stripped and frames repaired, replacing all rusted sections with new metalwork
- Wiring harness ordered ready for final build. Costed up making my own loom and decided it was false economy. The new loom looks great.
Last edited:
Steve Noakes
Active Member
- Posts
- 131
- Location
- Sussex
Engine before & after
Steve Noakes
Active Member
- Posts
- 131
- Location
- Sussex
Diffs and axles rebuilt - before and after
Last edited:
Steve Noakes
Active Member
- Posts
- 131
- Location
- Sussex
New swivel balls and rebuild
Steve Noakes
Active Member
- Posts
- 131
- Location
- Sussex
Leaf springs stripped, de-rusted, painted, rebuilt
Last edited:
