p38 4.6 misfire

and11 · May 7, 2016

Hi its been a a while since i was on here hope you all doing well i have now a 4.6hse gems engine
It starts first touch of the button and idles great
My problem is it will not rev above 1500 rpm then misfires But will go to over 3000rpm sometimes
I have changed stepper motor/cam sensor and checked plug leads are in the correct position on coil packs
I cant understand why it will still run if the cam sensor is disconected
I have just checked the relucter ring and found one tang/tooth mising on the inner circle could this be causing my problem
VERY sorry about a long thread

kevwill · May 8, 2016

MAF maybe. Not getting the right air/fuel mixture.

biketeacherdave · May 8, 2016

Maf 1st thing to check

Grrrrrr · May 8, 2016

Where is he? Diag might show something.

wammers · May 8, 2016

Grrrrrr said:
Where is he? Diag might show something.

He is obviously working on the crystal ball or make a guess theory principal.

.

and11 · May 9, 2016

Well no crystal ball lol checked relucter ring and found a tang mising so i have made another tang and welded it in place range is now runnig how it should thanks for the sugestions

Grrrrrr · May 9, 2016

Like being back at school. Answer was in the question.

and11 · May 11, 2016

Ye its was in the question but i did not no at the time that there was supposed to be 35 tangs i had 34 & a half hence one tang missing.
Therefore the answer i needed ( was in the question ) so my Question was baisicly should there be a tang missing and could it be causing the problem no body asked or be it answered as to what i meant all i realy got was sarcasam i wil not use this forum again or recomend it well not as a member

Grrrrrr · May 11, 2016

and11 said:
Ye its was in the question but i did not no at the time that there was supposed to be 35 tangs i had 34 & a half hence one tang missing.
Therefore the answer i needed ( was in the question ) so my Question was baisicly should there be a tang missing and could it be causing the problem no body asked or be it answered as to what i meant all i realy got was sarcasam i wil not use this forum again or recomend it well not as a member

There is good advice here but you may have to wait a bit until the nurse has finished with them and they've had their afternoon nap.

There is also, as you noted, a fair amount of what would probably be described as banter and sending up while people cogitate and wait for someone to spot the answer. It is an acquired taste. There is no nastiness in the intent as far as I'm aware.

and11 · May 11, 2016

thats ok

tomcat59alan · May 11, 2016

and11 said:
Ye its was in the question but i did not no at the time that there was supposed to be 35 tangs i had 34 & a half hence one tang missing.
Therefore the answer i needed ( was in the question ) so my Question was baisicly should there be a tang missing and could it be causing the problem no body asked or be it answered as to what i meant all i realy got was sarcasam i wil not use this forum again or recomend it well not as a member

Please try again when you have a thicker skin, you will be sorely missed.

sarcasam, what sarcasam

brianp38dse · May 11, 2016

All the odd coments and sarcasam help to keep the post at the top of the page and there for noticed , and gives us abit of light relief from the troubles of range rover owner ship.

odyssey · May 12, 2016

That's not sarcasm - THIS is sarcasm (read this in an Australian accent)
"Please try again when you have a thicker skin, you will be sorely missed. "

Dippypud · May 12, 2016

tomcat59alan · May 12, 2016

odyssey said:
That's not sarcasm - THIS is sarcasm (read this in an Australian accent)
"Please try again when you have a thicker skin, you will be sorely missed. "

And we haven't started on his spelling.

, yet.

Grrrrrr · May 13, 2016

tomcat59alan said:
And we haven't started on his spelling., yet.

Don't think English was his first language.

and11 · May 13, 2016

I was wrong to join this site originaly you can see from the comments above
why critisize sombodys spelling and i take offence at you assumeing that i may or may or not be english i have reported this comment i will defo use this site via asking questions on google MAY BE.
But this site is gona be in trouble if its only got certain people answering questions
ANYWAY support your local 81 if you can work that out

blue beasty · May 13, 2016

Grrrrrr said:
Don't think English was his first language.

Are you implying they're. ......

Merkin?

Saint.V8 · May 13, 2016

What have the Hells Angels got to do with it!?!

Landyzone is the premier place for information and advice....but also it is a prime place for a spot of 'ribbing' and 'micky taking'....as above it takes the heartache and frustration out of Land Rover ownership.

There is a 'Welcome' post in the Introduction Forum which lays out that Landyzone is not your 'Typical' forum.....perhaps having read this important post would have prepared you for what you will encounter here....after all that is why the post is there!!

In fact, if you missed it....here it is..... https://www.landyzone.co.uk/land-rover/welcome-to-all-new-members.48503/

New users/members to this site have been fair-warned what to expect in this welcome message....so, please do not get out of your pram, it is like moaning the coffee is hot when there has been fair warning!

and11 · May 13, 2016

I understand what you say so i am open to riddicule and if there is no malice intended thats ok so lets move on thanks

p38 4.6 misfire

Member

Active Member

Well-Known Member

Technician, Bodgit & Scarper Ltd

No longer with us, RIP

Member

Technician, Bodgit & Scarper Ltd

Member

Technician, Bodgit & Scarper Ltd

Member

Well-Known Member

Well-Known Member

Active Member

Never Knowingly Understood

Well-Known Member

Technician, Bodgit & Scarper Ltd

Member

Leaks an prone to bits dropping off

Dyed-in-the-wool 100% RR Junkie

Member

Similar threads