Disco 1 Oops! More work!

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Well, spent 3 and a half hours cutting the sill out tonight.
Really enjoyed finding the spot welds to drill them out

20190910_174009.jpg

Also found that a previous owner had welded the floor. I'm assuming there should have been a plastic plug to get to the body mount nut. Had to cut a hole instead!
20190910_180727.jpg

Sill all cut away. Look how rusty it was inside! Wow!

20190910_174000.jpg

Ill get some pics of the car minus a sill tomorrow. It was too dark!
 
Last edited:
Another 3 hours tonight.
Took some pictures of the underneath without the sill
20190911_164708.jpg

20190911_164716.jpg


Cut out the foot well and made a patch and butt welded it in.
Not cleaned and dressed the welds yet.
20190911_164652.jpg

20190911_184250.jpg

20190911_184314.jpg

Rear floor above the other mount next.
Just keep chipping away at it.
Mot runs out on Monday!
 
Kev12 said:
Nothing like a last minute repair ;)
Looking good so far
Click to expand...

Thanks mate. I'm covered in weld burns and cuts from the angle grinder because I took the guard off to get to those awkward places!
Rear floor tomorrow.
Then Saturday rust treat where the sill goes.
Cut and sort the box section sill.......... Blar Blar Blar zzzzzzzzzzz
Dreaming land rovers and tin worm!
 
Couple of hours play tonight.
Made a panel for the rear footwell
Difficult one to do but I think it came out okay?
20190913_183718.jpg
20190913_183724.jpg
And one of it held in place
20190913_183746.jpg
And welded in
20190913_190411.jpg
Sort the wheel arch tomorrow and the a and b post then I might actually be able to do the box section sill.
Happy days everyone...
 
Yesterday was a big day.
Made new panels to repair the A and B posts. B was better than the A.
Found out you have to remove both the wing and the front door to repair the A post :(
Any way. I cut the wing things off the body mount brackets and had my 150amp at full pelt to weld them to the 5mm box section. To my surprise I had to turn it down one setting.
Cut the box to length with an angle for the rear arch.
Box section then in and bolted with a jack to hold.
I then puddle welded where the carpet trim clips were. Figured I'd never see fit then in 5mm steel so think I'll just weld some m5 nuts down and get some pan head machine screws to fit the trim.
A and b post welded.
Just got the rear arch to do next.
Seam sealed with ever build.
Photos next :D
20190914_121002.jpg

20190914_121019.jpg
20190915_074024.jpg
20190915_074048.jpg
20190915_074039.jpg
20190915_074120.jpg
20190915_074139.jpg
20190915_074201.jpg
20190915_074154.jpg
 
Kev12 said:
You realise you won't be able to stop now? Full blown restoration incoming :cool:
Click to expand...
You maybe right....lol
Today I think I finished it apart from paint!
Made a panel to fix the rusty wheel arch. That was difficult on the curve but I think it looks alright.
Also did the door seal retaining strip and the sill closing panel /front of rear arch.
Bit novice but I think it's alright?
20190915_151924.jpg
20190915_151929.jpg
20190915_151945.jpg
20190915_195327.jpg
20190915_195331.jpg
20190915_195400.jpg

Funny colour stuff is aquasteel. Bit of red oxide tomorrow hopefully :D
 
You must log in or register to reply here.

Similar threads

Naf623
Disco 2 What fixings to use for the wheel arch liners?
Replies
2
Views
564
jamesDiscoTD5
jamesDiscoTD5
M
Freelander 1 VCU off for car how to test
Replies
2
Views
299
GrumpyGel
GrumpyGel
Rubberknees
P38 rear door window trims replacement
Replies
14
Views
1K
Rubberknees
Rubberknees
J
Whining/hissing nosie on accelerating
Replies
1
Views
812
Toonraider
T
MAF Diver
Disco 2 Rough idle in a V8 D2a — tried MAF, O2, sparks, leads
2
Replies
35
Views
3K
marjon
marjon
Back
Top