Old style glow plugs

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.

Faber

Member
Posts
53
Location
Berks
When the end of an early type glow plug breaks and disappears into the engine should I try to take steps to retrieve the bits or hope that they will be blown out?

I am concerned about damage, don't want to take the head off, but was thinking of turning the engine over with the new glow plug out.

Probably not enough pressure?

Any ideas or just wait for nothing to go wrong!
 
When the end of an early type glow plug breaks and disappears into the engine should I try to take steps to retrieve the bits or hope that they will be blown out?

I am concerned about damage, don't want to take the head off, but was thinking of turning the engine over with the new glow plug out.

Probably not enough pressure?

Any ideas or just wait for nothing to go wrong!
Can you explain a bit more clearly?

My reading of this is that the tip has broken off, and you have installed a new glow plug on top of the broken tip?

That isn't a good idea. The broken tip won't "disappear into the engine".
It is most likely still in the bottom of the hole, in which case it will be crushed in by the new plug on top of it, and very difficult to get out now.
The other possibility is that, if a very small piece has broken off the tip, it has been pushed though into the swirl chamber, in which case there is no way you will get it out without taking the head off.
 
Can you explain a bit more clearly?

My reading of this is that the tip has broken off, and you have installed a new glow plug on top of the broken tip?

That isn't a good idea. The broken tip won't "disappear into the engine".
It is most likely still in the bottom of the hole, in which case it will be crushed in by the new plug on top of it, and very difficult to get out now.
The other possibility is that, if a very small piece has broken off the tip, it has been pushed though into the swirl chamber, in which case there is no way you will get it out without taking the head off.
Thanks.
It looks as if I have made a cock up!

Faber
 
Yes.

Yesterday it was difficult to start but after a 15 sec crank it did and I went for about an hour before returning and checking the glow plugs.

It was then that I found no 4 had a broken end, and replaced it with a new one.

I was thinking of removing it, bringing the piston to tdc and inserting a thin magnetic tipped probe, but I guess that's too late or clutching at straws.

Faber
 
Yes.

Yesterday it was difficult to start but after a 15 sec crank it did and I went for about an hour before returning and checking the glow plugs.

It was then that I found no 4 had a broken end, and replaced it with a new one.

I was thinking of removing it, bringing the piston to tdc and inserting a thin magnetic tipped probe, but I guess that's too late or clutching at straws.

Faber
Try removing the new plug from the hole where the broken plug was, and putting a rag over the hole, and spinning it over.
A bit of the old plug may shoot out, so keep your eyes and fingers away while you are doing it.
If nothing comes out, replace the new plug, and carry on driving it, if it runs OK the small piece inside the swirl obviously isn't doing much harm. You will probably end up taking the head off sometime anyway, and the swirl chamber cap may well fall out when you do, so you can inspect it then.
 
Try removing the new plug from the hole where the broken plug was, and putting a rag over the hole, and spinning it over.
A bit of the old plug may shoot out, so keep your eyes and fingers away while you are doing it.
If nothing comes out, replace the new plug, and carry on driving it, if it runs OK the small piece inside the swirl obviously isn't doing much harm. You will probably end up taking the head off sometime anyway, and the swirl chamber cap may well fall out when you do, so you can inspect it then.
Thanks very much for your help.

Faber
 
Pig tail type glow plugs?
You might be lucky and the coil bit may still be in the pre combustion chamber.
 
Pig tail type glow plugs?
You might be lucky and the coil bit may still be in the pre combustion chamber.
Or it could have fallen through the port, into the cylinder, and out the exhaust valve.
Either way, if it is running OK, I doubt it is going to cause a problem now, so carry on as usual might be the best policy.
 
Thanks for all your advice. I tried today to retrieve any bits i) by inserting a thin magnet tipped probe and ii) turning the engine over withe the plug out, and I retrieved nothing.

A later compression test showed that the pot was OK ( at least at the moment ) and it starts well.

It is 43 years old and sometime the head will need to come off, but I am pleased it is still running and grateful for all the different advice I get from the group to enable me to keep it going.

Faber
 
Back
Top