Datatek
Well-Known Member
- Posts
- 45,063
- Location
- Near Poitiers SW France
Lockset code different from EKA? yes completely different.
P38A Nanocom near Lanarkshire?
- Thread starter jordanpc2
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
jordanpc2
Member
- Posts
- 19
- Location
- Lanarkshire
Nice one thanks for the info.... Bit of an update... Car still not driving... Will get to central locking soon..
Notice one of the wires going into bell housing opposite starter motor is frayed away. Hanging by a thread... Believe this is crank sensor? This wouldn't affect drive would it?
Notice one of the wires going into bell housing opposite starter motor is frayed away. Hanging by a thread... Believe this is crank sensor? This wouldn't affect drive would it?
- Posts
- 3,975
- Location
- Near Heathrow.
Bad crank sensor = no spark !!
jordanpc2
Member
- Posts
- 19
- Location
- Lanarkshire
That's what I thought... Starts ok so while the wire might be frayed .. it must be good enough
I’ve just bought a p38 I’m based in Cumbernauld
awkwardbob
Well-Known Member
- Posts
- 592
- Location
- Glasgow
sorry just spotted this as have been otherwise engaged for a while and hiding from the huge list of jobs I need to do on my car, but I have a nanocom and I’m in Glasgow.
It’s set up for Gems but it might be able to help with your key issues if you still have them
It’s set up for Gems but it might be able to help with your key issues if you still have them
Doolinjames
Active Member
- Posts
- 137
- Location
- denny
Hi mate I live in Denny got a Hawkeye for p38
Datatek
Well-Known Member
- Posts
- 45,063
- Location
- Near Poitiers SW France
The FOB does not need diagnostics to sync it to the car.
- Posts
- 19,317
- Location
- Buckinghamshire, UK. ('95 DT)
Coil may not be picking it up. Has RF receiver been unplugged? If so, put fob up to rear quarterlight where fob aerial is and press unlock button. Put key in lock and unlock. Hold fob up to rear quarterlight and press lock. Put key in lock and turn to lock. Repeat the procedure a few times. The microswitches in the door need to be fully working though.
The THOR can lose sync between the engine ECU and BECM and then you need to copy the code from the EMS to the BECM.
Doolinjames
Active Member
- Posts
- 137
- Location
- denny
Hi guys.got flashing lights on auto box and a fault on screen says shift to neutral what's this all about.
JUKE179r
Well-Known Member
- Posts
- 3,166
- Location
- Suffolkshire
Read this about the P38 fob:
Datatek
Well-Known Member
- Posts
- 45,063
- Location
- Near Poitiers SW France
Damp in the BECM
Doolinjames
Active Member
- Posts
- 137
- Location
- denny
Becm dried out and been unlocked by rova
Datatek
Well-Known Member
- Posts
- 45,063
- Location
- Near Poitiers SW France
Connectors dried and cleaned?
Doolinjames
Active Member
- Posts
- 137
- Location
- denny
Could no it be the ECU gearbox or transfer box ECU
Datatek
Well-Known Member
- Posts
- 45,063
- Location
- Near Poitiers SW France
The lights by the gear lever if I remember correctly come from the BECM.
- Posts
- 16,557
- Location
- Benfleet, Essex
Doesn't the decode of the XYZ switch by the BeCM enable the BeCM to light the correct light?
Have you tried cycling the gearbox from Hi-to-Lo and back a few times?
Have you tried cycling the gearbox from Hi-to-Lo and back a few times?
Doolinjames
Active Member
- Posts
- 137
- Location
- denny
Done that
Doolinjames
Active Member
- Posts
- 137
- Location
- denny
Any other ideas guys.could it be the xyz switch
Doolinjames
Active Member
- Posts
- 137
- Location
- denny
Does anyone know what 40 & 80 outstation is Is this SRS According to my Hawkeye it's the seats front
