MayorQuimby
Active Member
- Posts
- 290
Another thing to start selling... 
My Defender 90 rebuild
- Thread starter 200
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
200
Active Member
- Posts
- 939
- Location
- huddersfield
Another thing to start selling...
If only i had the time.
Managed to get one side done in between seeing to my wife's horse i will get the other done tonight.
- Posts
- 11,023
- Location
- North of the Wall
Back panels in the tub.
Where did you get your back panels from, mate? Were they Britpart ones? Mine have been hard work and I think I am going to have to scrap the near side one. It's looking like I might have had it in the wrong place when I drilled the holes through from the inner wing. Would rather not buy the same poorly built panel again if there are better ones available.
200
Active Member
- Posts
- 939
- Location
- huddersfield
I think they were from Ribble valley 4x4 on ebay mate, they weren't perfect and i had to do a little bit of trimming but nothing too bad and were pretty easy to fit. I had looked at the britpart one's and decided to leave them alone. I had to buy genuine corner post though as the one's from paddock didn't even meet the top capping they were 1/4" short and apparently i'm only the 3rd person to complain about them from the 1000s they have sold.
200
Active Member
- Posts
- 939
- Location
- huddersfield
Here you go mate but they don't have any listed but you can give them a bell.
Braking, Suspension items in Ribble Valley 4x4 LTD store on eBay!
Braking, Suspension items in Ribble Valley 4x4 LTD store on eBay!
- Posts
- 11,023
- Location
- North of the Wall
I think they were from Ribble valley 4x4 on ebay mate, they weren't perfect and i had to do a little bit of trimming but nothing too bad and were pretty easy to fit. I had looked at the britpart one's and decided to leave them alone. I had to buy genuine corner post though as the one's from paddock didn't even meet the top capping they were 1/4" short and apparently i'm only the 3rd person to complain about them from the 1000s they have sold.
Mine are britpart and a few dimensions have been out.
Spot the difference!
Setting them up has been a problem, I think, because I replaced the floor and the rear body member as mine was rotten. The holes where the tub lugs bolt to were gone. Unfortunately, this left me with few reference points to line up to. Didn't think too much of it when I rebuilt the tub, but now I realise I haven't had things lined up properly.
I'll look for Ribble Valley 4x4. Do they make their own?
200
Active Member
- Posts
- 939
- Location
- huddersfield
I couldn't tell you what make they are but they were out in the same place as your's but only by 1/4" though.
MayorQuimby
Active Member
- Posts
- 290
- Posts
- 11,023
- Location
- North of the Wall
200
Active Member
- Posts
- 939
- Location
- huddersfield
Cheers mate
i would love to but i just don't have the time at the minute. I have to get mine finished then it's something i will be looking at.
Derby7889
Active Member
- Posts
- 202
- Location
- Derbyshire
Liking those corner protectors, I reckon I might have to have a crack at making some of those!
I think I'm going to have to do something with my rear cross member first though :|
I think I'm going to have to do something with my rear cross member first though :|
200
Active Member
- Posts
- 939
- Location
- huddersfield
Take it down Hollinsclough in Derbyshire that lane will give you a reason to put them on.
Derby7889
Active Member
- Posts
- 202
- Location
- Derbyshire
200
Active Member
- Posts
- 939
- Location
- huddersfield
MayorQuimby
Active Member
- Posts
- 290
I'm already putting money aside for the rock sliders and corner protectors.
Just lengthen the sliders accordingly for a 110 and leave the corner protectors without the holes...
Just lengthen the sliders accordingly for a 110 and leave the corner protectors without the holes...
200
Active Member
- Posts
- 939
- Location
- huddersfield
I'm already putting money aside for the rock sliders and corner protectors.
Just lengthen the sliders accordingly for a 110 and leave the corner protectors without the holes...
Ok Matey
200
Active Member
- Posts
- 939
- Location
- huddersfield
Just test fitted the rear door and it fits also test fitted the rock sliders as i made these of my old chassis measurement so was just hoping they would fit the new one.
also test fitted the rock sliders as i made these of my old chassis measurement so was just hoping they would fit the new one.
MayorQuimby
Active Member
- Posts
- 290
Looking good buddy
