M and S lights, limp mode, p0743

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
sierrafery said:
Did you change the oil and filter with the procedure shown in the manual? that's important... if yes then IMO better replace that solenoid cos that valve block seems fubar, though go into the autobox ECU with nanocom and give it a "reset adaptive values" maybe it helps but i'm not confident with this... are you sure that the valve block was removed from a D2 cos there are same autoboxes on RR P38 too which are not working the same ?
Click to expand...

this time not the filter because we did that 3 weeks ago also with the oil then. We filled it like the manual said. We also tried with the nanocom the reset adaptive values. He said the valve came from a D2 but is there maybe a difference between the build years ? The person I bought it from said it came from a D2
 
I dont know what happenned then, sorry, when it comes to scrap removed from old vehicles nothing is ruled out, try to replace the solenoid from the original block but as long as it's not new i have no other ideea, that solenoid is not so expensive so IMO you should have bought a new one and get done with it... are you sure you didnt missalign the XYZ switch ? do you see all the selections correctly on the console too ?
 
Reggaerover said:
this time not the filter because we did that 3 weeks ago also with the oil then. We filled it like the manual said. We also tried with the nanocom the reset adaptive values. He said the valve came from a D2 but is there maybe a difference between the build years ? The person I bought it from said it came from a D2
Click to expand...

image one is the one I bought and image 2 is the one that came from my car today
 

Attachments

  • 1ED1431C-3B69-48E1-B41A-43BBCC725173.jpeg
    1ED1431C-3B69-48E1-B41A-43BBCC725173.jpeg
    71.9 KB · Views: 90
  • B595BE3A-5BBB-48BA-A5BB-D5187AC80B56.jpeg
    B595BE3A-5BBB-48BA-A5BB-D5187AC80B56.jpeg
    76.3 KB · Views: 97
sierrafery said:
I dont know what happenned then, sorry, when it comes to scrap removed from old vehicles nothing is ruled out, try to replace the solenoid from the original block but as long as it's not new i have no other ideea, that solenoid is not so expensive so IMO you should have bought a new one and get done with it... are you sure you didnt missalign the XYZ switch ? do you see all the selections correctly on the console too ?
Click to expand...
I know but I need my car a lot and the one I ordered was only going to been send the 26th of February. So maybe 1 month until I got the part and I bought the one from the Netherlands Wednesday and today it arrived and with the ‘test’ drive the m and s lights didn’t show up
 
Yes next to the gear lever to the lights also follow every stand. I think the only thing to try is open again and look for things that don’t seem right or just swap the valve block again with the old one and change the solenoid with it
 
You must log in or register to reply here.

Similar threads

Andrewoldold
M&S lights no crank / potentially immobilised?
Replies
1
Views
314
sierrafery
sierrafery
archwayanimal
M and S issue
Replies
13
Views
993
sierrafery
sierrafery
F
Disco 3 (LR3) Dreaded Limp Mode - Suggestions?
Replies
13
Views
1K
ffisher
F
archwayanimal
Fault code 0753 Solenoid 1 valve?
Replies
14
Views
919
Stanleysteamer
Stanleysteamer
N
Limp mode
Replies
0
Views
303
Nickandstan
N
Back
Top