Disco 1 Lost drive to rear wheels

fozt · Sep 4, 2016

Hi guys,

I was offroading earlier today, and I went up a steep incline and there was a loud bang - i assumed it was something hitting the floor. I got out and had a look and everything seemed fine - i then realised I only had drive to the front wheels.

How can I diagnose if it's half shaft or diff? Or something else?

Cheers.
Foz

Magicgrotto · Sep 4, 2016

Hi Foz pull your half shafts out !

fozt · Sep 4, 2016

Magicgrotto said:
Hi Foz pull your half shafts out !

Never done it before - is it just those 6 bolts and they slide out??

Disco1BFG · Sep 4, 2016

Yep. Worth watching for sharp bits - just in case.

Magicgrotto · Sep 4, 2016

Yep as Disco say's

If splyny bits still on end it's not that bit !

It's the other bit !

Steve

fozt · Sep 4, 2016

Hi guys,

I can get 4 out of 5 bolts undone but the last one won't budge - I can't get the socket on deep enough to get a good grip, and it's rounding off the top of the head slightly. The socket went on ok on all of the other bolts - can I get super thin sockets or something?

Any suggestions please?

Foz

neilly · Sep 4, 2016

I am confused why you would need thin sockets, I would have thought you had lots of access to the bolt heads.

Can you post a photo?

Cheers

Magicgrotto · Sep 4, 2016

If in dowt give it a clout !

you sure it's not muck keeping socket off ?

Steve

fozt · Sep 4, 2016

Photo should be attached.

Socket won't fit behind the gap nicely - I've tried cleaning it out Incase it was full of mud, but the socket still won't fit on properly.

Cheers.

The Mad Hat Man · Sep 4, 2016

hammer the socket on.#

is it a 6 or 12 point?

why have you removed the wheel?

Magicgrotto · Sep 4, 2016

GIVE IT A GOOD SMACK with a HAMMER on the end

(Or two or three)

& a 6 point socket & it should come out

Steve

neilly · Sep 4, 2016

Very Strange,

Other option is if you have a dremmel then a bit of TLC on the drive flange.

Cheers

Magicgrotto · Sep 4, 2016

ps you aint gunna break owt coss it already is !

fozt · Sep 4, 2016

I tried hammering the socket on, but it still won't go on properly or flush and that is what ended up rounding off the top of the head.

I'm using a 6 point socket.

The wheel is off because I tried to get a set of mole grips on, which didn't help.

Tried the hammer trick!

ill probably end cutting it off...

Thanks for the responses!

Foz

Magicgrotto · Sep 4, 2016

SMACK the BOLT not the socket

Sharp smack with hammer & chisel !

Disco1BFG · Sep 4, 2016

Always worth trying to tighten it first too - it might just release the corrosion - plus, as others have said - the hub is a big lump, and some "percussive maintenance" is unlikely to hurt it

fozt · Sep 4, 2016

I did actually manage to get it to loosen a tiny bit, but then it started rounding off - that's why I was hoping the mole grips would help but ultimately they didn't!

Anyone have the part number for replacement bolts?

I'll just carefully go at it with an angle grinder!

Thanks for the replies all.

Foz

The Mad Hat Man · Sep 4, 2016

weld a nut on top to extend the head?

whereabouts in Kent?

Magicgrotto · Sep 4, 2016

M/H/M you can't miss were he lives !

His house is the 1 with a dico on the drive with only 3 wheels & NO drive to the back wheels !

Hope this helps ?

The Mad Hat Man · Sep 4, 2016

Magicgrotto said:
M/H/M you can't miss were he lives ! His house is the 1 with a dico on the drive with only 3 wheels & NO drive to the back wheels !
Hope this helps ?

Not when i am trying to get him some help

Disco 1 Lost drive to rear wheels

Active Member

Well-Known Member

Active Member

Well-Known Member

Well-Known Member

Active Member

Well-Known Member

Well-Known Member

Active Member

Attachments

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Active Member

Well-Known Member

Well-Known Member

Active Member

Well-Known Member

Well-Known Member

Well-Known Member

Similar threads