just broke my 200tdi within 10hours of owning it

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Stupid as this is going to sound, you said both prop shafts turn but you didn't say if the vehicle was moving or not:

IF the vehicle was rolling slightly (on a hill for example), the props were both turning but you had no drive - I'd suggest the wheels were turning the props so diffs are o.k and you have a transfer box, gearbox or clutch problem (transfer box would be my guess after 80miles in difflock).

In case you've not read about the little gearstick here's some pointers;

THE PICTURE ABOVE IT TELLS YOU WHAT IS WHERE!

High range, out of difflock for on the road
Low range, out of difflock for offroad, though high will often do

Engage difflock only when it looks like you might lose traction and come back out of it as soon as you can, if the light stays lit - it's not come out properly and reversing will usually cure this, you have high and low in difflock too - use whichever is suitable.

Low range for going down hills, NOT the brakes, steep and unfirm slopes, use the difflock too but don't forget to come back out of it asap, generally - 1st,2nd possibly 3rd for going down hills - don't touch the brakes, the gears will slow you just fine.

If it starts sliding downhill, accelerate as little as at takes to stop this - Brakes will make matters a whole lot worse.

A standard landrover drivetrain is permanently 4wd - you can't put it in 2wd or anything else, the little stick only does as I've explained above. The difflock just locks the front and rear axles to turn the same.

Without the difflock on, complete loss of traction on one wheel will have you stuck (both diffs pick the easiest to turn)

With difflock on complete loss of traction on ONE wheel on BOTH axles will see you stuck
 
osr hub leaking oil (from the back of the wheel right?) will be hub oil seal but might be due to bearing loose/knackered, jack the wheel up and check it spins nicely with no noise (the pads might rub, listen for rumbling) and check for play in the bearing, the wheel will wobble if problem exists. Infact, check all the wheels. If there is play in front wheel and its only noticable when you hold top and bottom it could be swivels though. That half shaft you posted is 10 spline so you almost certainly have 10 spline all round (unless front has been changed but highly unlikely). It also looks to me like its been hammered, is it me or are the splines twisted? They should be straight, without a kink. You might want to replace them. When you get diff out it will be very obviously broken.. You need to read a load of tutorials and guides, there are loads about with lots of photos. Get a 9/16 spanner and socket if you dont have one. Good luck, truck looks nice but i suspect you will be posting more threads!
 
Thanks for all the relpy's.
I ve just been outside and had another look.
when I put it in 1st and bring the clutch up the is loud cluncking noise, doesnt matter if in diff lock or high range.
both propshafts are moving when the clutch is engaged and the car is stationary in first gear, in diff lock or high range.

then I turned the engine off whilst in first gear and a mate started rocking the car as i was watch the prop shafts, neither of them were turning as we were pushing it back and forth.
this would suggest its the diffs, right?
 
Wheels on floor-prop turns-wheels dont = something broke between the prop and wheel. Can be diff or shaft at rear and diff/shaft/cv joint/drive flange at front. When you did this test btw did you have the rear shafts bolted back in or on the floor?
 
Wheels on floor-prop turns-wheels dont = something broke between the prop and wheel. Can be diff or shaft at rear and diff/shaft/cv joint/drive flange at front. When you did this test btw did you have the rear shafts bolted back in or on the floor?

Yes the half shafts were bolted back in when I rolled it back and forth.
 
get a mate to lay under the back, behind the rear diff - and then try and drive forward - see if he can hear or feel out.

I got a mate to lie under the rear and he was listening for noises from the diff but he said there were no noises coming from it when I was revving it up in 1st and both prop shafts were spinning.
 
osr hub leaking oil (from the back of the wheel right?) will be hub oil seal but might be due to bearing loose/knackered, jack the wheel up and check it spins nicely with no noise (the pads might rub, listen for rumbling) and check for play in the bearing, the wheel will wobble if problem exists. Infact, check all the wheels. If there is play in front wheel and its only noticable when you hold top and bottom it could be swivels though. That half shaft you posted is 10 spline so you almost certainly have 10 spline all round (unless front has been changed but highly unlikely). It also looks to me like its been hammered, is it me or are the splines twisted? They should be straight, without a kink. You might want to replace them. When you get diff out it will be very obviously broken.. You need to read a load of tutorials and guides, there are loads about with lots of photos. Get a 9/16 spanner and socket if you dont have one. Good luck, truck looks nice but i suspect you will be posting more threads!

I think its just the way I took the pic with my fone, the reflection of the sun in the oil on the shaft makes it look twist but when I inspected it, it looked totally fine.
 
also, when in neutral the propshafts are spinning, but you can stop it by grabbing the shaft with your hand, I assume thats just clutch drag as they dont spin when I dip the clutch.
 
im not too sure on last post but like said if a prop turns and no wheels on the axle does something is broke, it looks like the fault on the rear is the diff. get it removed to confirm, you will probably find a few pieces in there. You will need a 10 spline diff with a 4 bolt flange.. If you fix the rear you can still move the car (very gently and not very far) with diff lock on, u might want to move it to somewhere else to sort the front, i dont know.
 
think that's normal mate, would deffo look at the diffs. I've never pulled one apart but saw a mate swap broken bits in his and have it up and running in an hour so can't be that bad.
 
how about we save allll this hassle, ill come and have a look at it if you like,i live in oxford and have had way to much experience with broken halfshafts and diffs for my liking,but experience could come in handy here . let me know mate.
 
i did read on the first post he was going enfield to oxford, and i assume your at oxford uni? the road in your picture you uploaded looks familiar,especialy the house behind your landy, but as i said,pm me or something and if need be ill give you a hand, us landy owners stick together, i might even show you how the transfer box gearknob works ;)
 
i did read on the first post he was going enfield to oxford, and i assume your at oxford uni? the road in your picture you uploaded looks familiar,especialy the house behind your landy, but as i said,pm me or something and if need be ill give you a hand, us landy owners stick together, i might even show you how the transfer box gearknob works ;)

That would be awesome! I live in is where its parked on because its too wide to fit down the driveway.
 
Last edited by a moderator:
That would be awesome! I live in is where its parked on because its too wide to fit down the driveway.

You've just told any thieving git looking at this forum where to grab a landy or it's part's:doh:
 
Last edited by a moderator:
669hoff, he has a fair point,I would remove that post! You never know who's on here!! Mr.fleg, thankyou :) I'm always willing to help anyone,I know how annoying it is trying to fix something when you don't know where to start!! That's how I've learnt! If anybody else needs a shout with anything,mechanical,electrical or welding in the oxfordshire area,just let me know!!
 
Back
Top