It was too good to be true

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
flookyk

flookyk

Active Member
Posts
177
Location
CO Durham
oh bugger ..... Thought it was going too well.

Car passed it's MOT after replacing the drop links on the anti roll bar.
Just had a good run down from North East to Birmingham, car going well until just pulling into hotel car park and notice the temp gauge stating to climb.
Parked up and there is water and steam coming out of back of engine near bulkhead over the gearbox.

It is diesel P38. Is someone going to be kind and tell me there is a coolant pipe at the back of the engine and it is not the cylinder head gasket that has failed ..... Please .... Pretty please. :-(
 
flookyk said:
oh bugger ..... Thought it was going too well.

Car passed it's MOT after replacing the drop links on the anti roll bar.
Just had a good run down from North East to Birmingham, car going well until just pulling into hotel car park and notice the temp gauge stating to climb.
Parked up and there is water and steam coming out of back of engine near bulkhead over the gearbox.

It is diesel P38. Is someone going to be kind and tell me there is a coolant pipe at the back of the engine and it is not the cylinder head gasket that has failed ..... Please .... Pretty please. :-(
Click to expand...

There is steel coolant pipe from memory on omega diesel (same engine)
 
flookyk said:
oh bugger ..... Thought it was going too well.

Car passed it's MOT after replacing the drop links on the anti roll bar.
Just had a good run down from North East to Birmingham, car going well until just pulling into hotel car park and notice the temp gauge stating to climb.
Parked up and there is water and steam coming out of back of engine near bulkhead over the gearbox.

It is diesel P38. Is someone going to be kind and tell me there is a coolant pipe at the back of the engine and it is not the cylinder head gasket that has failed ..... Please .... Pretty please. :-(
Click to expand...

Favourite would be that bastard of a metal pipe across back of head possibly the C shaped hose that goes to it. If it is and you fit a new one use proper hose clips not those silly expanding ones.
 
Just managed to have a look after topping up with water.

I can see it dripping out where that rear pipe joins the rear nearside of engine just does not appear to be able to get to it without removing the inlet manifold.

May get trailered home on Thursday and sort it out there.

.
 
flookyk said:
Just managed to have a look after topping up with water.

I can see it dripping out where that rear pipe joins the rear nearside of engine just does not appear to be able to get to it without removing the inlet manifold.

May get trailered home on Thursday and sort it out there.

.
Click to expand...

You can't, unless you are a gynecologist and can paper your hallway through the letterbox. :D
 
Had early brekkie at hotel and took the inlet manifold off.
The pipe where the clamp is on has been crushed narrower over time so the clamp is not making it watertight anymore.

If there is anyone near J2 of M42 that has a worm O clamp around 25mm tightened I would be grateful, at least it should get me home tomorrow so I can change the pipe.
Id not may have to see if there is enough pipe to cut off the crushed end, reattach with original clamp.
 
flookyk said:
Had early brekkie at hotel and took the inlet manifold off.
The pipe where the clamp is on has been crushed narrower over time so the clamp is not making it watertight anymore.

If there is anyone near J2 of M42 that has a worm O clamp around 25mm tightened I would be grateful, at least it should get me home tomorrow so I can change the pipe.
Id not may have to see if there is enough pipe to cut off the crushed end, reattach with original clamp.
Click to expand...

Ya want a jubilee clip
 
Heat has got to sping clip, don't cut hose if it is undamaged, also have look at lzir map and see if anyone close.
 
Looking now
Big ginga beard?
Dog47
Tomseries3tom
Sirus
Bigsi13
For starters

Perhaps
MarkL
 
Location Westmeads Hotel just off J2 M42, will PM phone no to anyone that can help.
I appologise in advance if not imeadiate replie as in meetings at hotel and can only reply during coffee breaks and lunchtime until meeting finishes.

Thanks for the efforts from people on here it is appreciated
 
Last edited:
You must log in or register to reply here.

Similar threads

L
Too many beads in compressor
Replies
0
Views
351
Liverghouls
L
NiallRussell
need help, can you diagnose this...
Replies
4
Views
348
NiallRussell
NiallRussell
M
P38A Finally have time to be back on forums again
Replies
4
Views
339
brianp38dse
brianp38dse
J
High Mileage Freelander 2 - am I crazy or could this be a good buy?
Replies
3
Views
662
Nodge68
Nodge68
G
Land Rover 300tdi clutch not disengaging after engine out
Replies
8
Views
2K
miktdish
miktdish
Back
Top