Ignition key and manifold

Steve Ashworth · Jan 22, 2013

I am getting the ignition key warning...
Message tells me the key is in when I turn ignition off - back one step on the key.
I turn it back two more steps to remove key and message goes. Then when I open a door the ignition key message comes back on and car beeps. Message goes off after about 15 second delay. Should this sequence of events occur?
Have to lock door manually-key fob won't work as car thinks key is in.
I have tried the graphite powder and electrical contact cleaner with nil improvement.
Do I need to replace the key barrel and if so where can I get one.is it a straightforward swap if I keep my fob?
I am still struggling to find a drivers side exhaust manifold.any ideas- if I can't find one is it feasible to repair / weld mine?
I need to fix this as car sometimes stalls on low revs.
Thanks in advance.

rewmer · Jan 23, 2013

It's just a sticky switch in the barrel. A good squirt of releasing spray and a good wiggle of the key should fix it.

Datatek · Jan 23, 2013

Flush it out with a non residue contact cleaner.

Grit Valve · Jan 23, 2013

Don't think the cold weather helps Either.mine has just started doing it I have not got spray yet , but I have noticed in the morning the ignition barrel is stiffer than when the car has had a proper warm up inside .

dave4x4 · Jan 23, 2013

+1 Contact cleaner, let it dry out then a squirt of graphite powder.

Steve Ashworth · Jan 23, 2013

Thanks,
I've already done those things except more graphite.
I will try it again...
How long should i leave contact cleaner take to dry in barrel.

Cheers

Grit Valve · Jan 23, 2013

Steve Ashworth said:
Thanks,
I've already done those things except more graphite.
I will try it again...
How long should i leave contact cleaner take to dry in barrel.

Cheers

If you got an air line that helps budge stuff and dry quick if not it Evaporates pretty quick

gencybay · Jan 23, 2013

defender300td1 said:
Don't think the cold weather helps Either.mine has just started doing it I have not got spray yet , but I have noticed in the morning the ignition barrel is stiffer than when the car has had a proper warm up inside .

Must be one of those millennium buggery things. Mine has started doing it over the past week or so.

G~

Grit Valve · Jan 23, 2013

gencybay said:
Must be one of those millennium buggery things. Mine has started doing it over the past week or so.

G~

It's called ignorabarrel virus

Steve Ashworth · Jan 23, 2013

Cheers, I'll give it another good squirt and a good blast of air...

Any suggestions regarding the manifold?

Cheers

Grit Valve · Jan 23, 2013

Steve Ashworth said:
Cheers, I'll give it another good squirt and a good blast of air...

Any suggestions regarding the manifold?

Cheers

I'm not Psychic

Grit Valve · Jan 23, 2013

Ok i will have to presume its a petrol as you have said drivers side although the diesel is on that side too ! Our sponsor emmots has some as I've just seen them on ebay if not ebay has loads .

Steve Ashworth · Jan 23, 2013

Lol
Sorry defender, was referring to earlier thread.
Got a few issues with noise when cold and now rough running/stalling on low revs.
Checked exhaust manifold as advised on drivers side to find it leaks on last joint and the concertina section. Can't find replacement, that's what I referred to...

Grit Valve · Jan 23, 2013

Range Rover P38 Exhaust Manifolds Pair + Warranty | eBay
RANGE ROVER P38 V8 Exhaust manifolds the pair | eBay
RANGE ROVER P38 THOR V8 4.6 4.0 EXHAUST MANIFOLD 99 TO 02 DRIVERS OR PASSENGER | eBay
Not sure what year yours are think they changed after 1998 but don't hold me to this as I'm not a petrol head

Steve Ashworth · Jan 23, 2013

Mine is a petrol 4.0.
It's a 2001 model.
I tried google and eBay and all I got was gaskets loads of them...
Must have had bad filters set?
Also looked on Emmotts web site n there weren't any listed.
Will try again.

kevwill · Jan 23, 2013

I've got same problem on drivers side manifold. Small hole in the flexi bit. Sure I did it when removing heads for gasket change. I'm gonna have a go at rewelding it first. Done a temp repair with one of those metal exhaust repair straps with some exhaust putty (I left the horrible heat shields off). Hopefully it will last until some warmer weather arrives.

Steve Ashworth · Jan 23, 2013

If I can't find one I will have to try weld mine.
Read an article on someone who had this done by a pro welder but could not refit due to 3mm distortion on one flange , presumably due to heat...
A bit surprised I can't find one as it seems to be a common problem-thought there'd be an established after market...

jamesblake · Jan 23, 2013

+1 on graphite lube....got mine from maplin....

Steve Ashworth · Jan 23, 2013

Tried lots more contact cleaner, blasted with air line and tried more graphite but still get "ignition key in" message when door opened...

Barrel looks to ping out ok with key.

Problem must be more then just sticking.

Has anyone actually replaced the barrel?

Cheers,

Grit Valve · Jan 23, 2013

Steve Ashworth said:
Tried lots more contact cleaner, blasted with air line and tried more graphite but still get "ignition key in" message when door opened...

Barrel looks to ping out ok with key.

Problem must be more then just sticking.

Has anyone actually replaced the barrel?

Cheers,

Steve it must be jammed its it freezing where you are just out of Curiosity

Ignition key and manifold

Active Member

Well-Known Member

Well-Known Member

2000 4.6 Vouge

Active Member

Active Member

2000 4.6 Vouge

gatvol

2000 4.6 Vouge

Active Member

2000 4.6 Vouge

2000 4.6 Vouge

Active Member

2000 4.6 Vouge

Active Member

Active Member

Active Member

Active Member

Active Member

2000 4.6 Vouge

Similar threads