Southernlandy
Active Member
- Posts
- 523
- Location
- Hampshire
Security wise, wouldn't the blue on fit through the gap in the gate into your back garden? It would be more secure than leaving it around the front?
Here we go again, Project "Red shed"
- Thread starter aaronmorris
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
SupraAyf
Active Member
- Posts
- 171
- Location
- Durham City
aaronmorris
Head's a shed
- Posts
- 6,369
- Location
- Doncaster
Here we go again!!!
Yep
Although I have a feeling this is going to be a long project I've thought about it mate, Doesn't fit, If it did I'd build/strip them round there as well so all the nosey buggers cant see me.
Loads of traffic around me both on foot and cars and people are always being nosey down the drive
The blue one would fit through my gate quite easily, Aaron
I'm sure it would :boink: cheeky twunt
SupraAyf
Active Member
- Posts
- 171
- Location
- Durham City
aaronmorris
Head's a shed
- Posts
- 6,369
- Location
- Doncaster
Well the weather f*cked my plans up today.
Sat around most of the day, Got to about 3 ish and thought I can't not do anything today. So off I trundled in the rain.
Only had an hour or so, But managed to get the trans tunnel, Floor pans and seatbox out.
[/URL][/IMG]
Sat around most of the day, Got to about 3 ish and thought I can't not do anything today. So off I trundled in the rain.
Only had an hour or so, But managed to get the trans tunnel, Floor pans and seatbox out.
- Posts
- 11,023
- Location
- North of the Wall
Been chucking it down here too, driving me mad
Decided to take my new doors apart, but got a bit stuck there too.
Was hoping to get to rolling chassis by the weekend, but that is fading fast.
Ohhh, for a double garage!
Decided to take my new doors apart, but got a bit stuck there too.
Was hoping to get to rolling chassis by the weekend, but that is fading fast.
Ohhh, for a double garage!
aaronmorris
Head's a shed
- Posts
- 6,369
- Location
- Doncaster
Been chucking it down here too, driving me mad
Decided to take my new doors apart, but got a bit stuck there too.
Was hoping to get to rolling chassis by the weekend, but that is fading fast.
Ohhh, for a double garage!
Oh how I'd love a double garage
If you've got the axles painted and ready it'll only take an hour to put the axles under. Would be a nice milestone
Even if it is in the rain. F*cks me of this rain as given a good day and a bit it'd be completely in bits so I can decide what to do.
- Posts
- 11,023
- Location
- North of the Wall
Problem is, I've got the radius arms, trailing arms etc at my local Landy specialist to get new bushes pressed in. When I get them back I'll need to touch up the primer, paint with top coat (going to be the same as the Landy), then lacquer.
Rear axle is painted up with two coats of rustoleum. Still got the swivel seals to change on the front. One side I've managed to get the studs out of the end of the axle. Had to grind heads off bolts then extract remaining studs. Planned to do the other today, but rain stopped play!
I've decide to experiment with painting this axle! I've first painted it with 'Aqualsteel', the rust inhibitor I'm then going to paint the rustoleum over that. I'll be able to compare the lifespan of the paint on the front and back axles.
So, waiting to get the bushes in and the rain to stop!
Rear axle is painted up with two coats of rustoleum. Still got the swivel seals to change on the front. One side I've managed to get the studs out of the end of the axle. Had to grind heads off bolts then extract remaining studs. Planned to do the other today, but rain stopped play!
I've decide to experiment with painting this axle! I've first painted it with 'Aqualsteel', the rust inhibitor I'm then going to paint the rustoleum over that. I'll be able to compare the lifespan of the paint on the front and back axles.
So, waiting to get the bushes in and the rain to stop!
aaronmorris
Head's a shed
- Posts
- 6,369
- Location
- Doncaster
Yeah bushes are something I usually leave, But this being older than the others I've done, The bushes aren't brilliant.
So I intend to invest in a press
Be interesting to see if the axle holds up any better.
And hopefully this rain ****es off for both yours and mines sake.
aaronmorris
Head's a shed
- Posts
- 6,369
- Location
- Doncaster
Had another couple of hours on it this afternoon.
Had George's missis watching me out the window
So disconnected the rear wiring loom, Unbolted seat belt mounts, Tub to crossmember bolts.
Removed sills.
Then lifted the tub off.
Chassis is actually not bad, Looked **** to start with but it's just old crappy underseal that's coming off.
Only found 1 hole so far and that was me with me big 'ammer
Will make a decision about it's future when I've been over it properly and it's fully stripped.
Bulkhead wants a foot on the o/s and a top corner on the n/s.
[/URL][/IMG]
[/URL][/IMG]
Next job, Remove the fuel tank. And that was it for the day.
[/URL][/IMG]
Infact one more thing. Bit of nothing but wanted to see what the old paint would come up like.
Gave it a quick rub on one corner with some g10 and it came up a treat. If I didn't have to do some repairs on the body I'd be tempted to do it all and leave it like that.
[/URL][/IMG]
Had George's missis watching me out the window
So disconnected the rear wiring loom, Unbolted seat belt mounts, Tub to crossmember bolts.
Removed sills.
Then lifted the tub off.
Chassis is actually not bad, Looked **** to start with but it's just old crappy underseal that's coming off.
Only found 1 hole so far and that was me with me big 'ammer
Will make a decision about it's future when I've been over it properly and it's fully stripped.
Bulkhead wants a foot on the o/s and a top corner on the n/s.
Next job, Remove the fuel tank. And that was it for the day.
Infact one more thing. Bit of nothing but wanted to see what the old paint would come up like.
Gave it a quick rub on one corner with some g10 and it came up a treat. If I didn't have to do some repairs on the body I'd be tempted to do it all and leave it like that.
-Defender110-
Well-Known Member
- Posts
- 1,054
- Location
- limerick, Ireland
you dont hang around lad! want to com over to ireland for the weekend and take the body off mine??
Rasher
Active Member
- Posts
- 434
- Location
- Bakewell Derbyshire
a week!
he only needs a dry day.
he only needs a dry day.
aaronmorris
Head's a shed
- Posts
- 6,369
- Location
- Doncaster
you dont hang around lad! want to com over to ireland for the weekend and take the body off mine??
Haha, Road trip to Ireland
It's finding a driver that's ****ing me of at the mo. Yep, Given one nice day and it'll be on the floor in a thousand pieces
Cheers
Paint takes ages mate, Painted the last 2 project and brothers 90. It's the prep that's the worst bit, Actually quite like the painting.
Landyfox
Well-Known Member
- Posts
- 4,489
You mean it's not rebuilt yet matey.?!
- Posts
- 11,023
- Location
- North of the Wall
The chassis looks in pretty good nick, How old is the Landy, marra?
The tank looked good too. The seam looks spot on. I'm not looking forward to cleaning up the seam on mine in case it falls in two
The tank looked good too. The seam looks spot on. I'm not looking forward to cleaning up the seam on mine in case it falls in two
RodneyA
Active Member
- Posts
- 295
- Location
- Ayrshire, South West Scotland
That's what happened to my tank when I took it off and cleaned it up
- Posts
- 11,023
- Location
- North of the Wall
ohh, bugger! :doh:
aaronmorris
Head's a shed
- Posts
- 6,369
- Location
- Doncaster
by 'eck tha cracking on with that Aaron
well jel mate
Steady away mate Bloody rain doesn't help, No point rushing anyway as I've got **** loads to sort out
Mainly find a Daf 45 (and driver) Or an engine and box (although I'd rather not go down this route)
Decide if I want to buy a glav chassis
Source disc brake back axle.
Sell old td to recoupe some funds
:blah: :blah: :blah: There's loads to sort anyway
So things will slow down shortly.You mean it's not rebuilt yet matey.?!
Cheeky twunt
As above mate. Steady away. The chassis looks in pretty good nick, How old is the Landy, marra?
The tank looked good too. The seam looks spot on. I'm not looking forward to cleaning up the seam on mine in case it falls in two
Chassis is better than I thought it would be. I was thinking galv chassis again but seems a shame to scrap a good chassis. Still not 100% on which way to go yet.
Landy is an 86 mate.
Haha my last one had a hole in it where someone had screwed the floor down :doh:
That's the problem with rebuilds, Everything looks fine and dandy when you take it off, But when you attack it with a hammer, screwdriver, wire brush or whatever your weapon of choice may be. It ends up f*cked. Or is it me being heavy handed
Similar threads
