help with my 05 freelander 1.8 litre petrol

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
C

chris chapman

New Member
Posts
15
Hi All ...

I am having a major problem with my 05 freelander 1.8 petrol.

Im no mechanic and this is my first freelander i have bought, the problem is that i can drive a few days without a problem and then all of a sudden as I'm driving the freelander starts to jerk a little and then just cuts out - if i attempt to restart it immedistely it just swings the motor but will not start. I leave it for 2 or 3 min and then restart it and it fires up immediately again , i drive for another 2 miles and the car repeats the process ... the last time being yesterday on the M3 !!! the car stopped 6 times before i managed to get back to Basingstoke !!

its almost as if it feels like their is a cut out sensor just switching the motor off or maybe the petrol pump not pushing the fuel through !! im just taking a shot in the dark here, other days i can ride perfectly with nothing happening and then all of a sudden the process starts again, the car temperature gauge is perfect and the freelander is not overheating ... please help !!!! does anyone know a good mechanic in basingstoke that can help me ...
 
Welcome to the forum :). Sounds like a tricky problem, I haven't heard of much like it. You're in luck though I believe some of our most knowlegable members live in the Basingstoke area and I'm sure they will know a good place to get it seen to.

Will.
 
I had the local repair shop have a look, they ran diagnostics which gave them petrol/air mix problems/errors but nothing else that could be causing the symtoms I'm getting ... no warning lights coming at all .... seems to jerk before engine cuts out, almost seems like no petrol is getting through .... hell i don't know !! if the repair shop cant find the problem i really got my back to the wall on this one .
 
Ah! Crank sensor tends to leave no errors! If the signal stops it just assumes its stalled or something! Obviously it's a bit of an educated guess:) but they also tend to break down with heat, so long trips. But are fine when cold, short trips! Something to look at:D
 
Hi Chris
Had a 1.8 FL that would cut out ocassionlly, would also sometimes 'hunt' slightly on tickover. eventually a mechanic noticed that diagnostics showed the second lamda sensor giving a very constant reading (1st sensor reading was fluctuating normally) Tickover hunting was being caused by the engine managment system switching beween lean & rich (presumably because it was getting a false reading from the 2nd lamda sensor) Changed 2nd lamda sensor, car ran ok afterwards, tickover more even & didn't cutout again.
Might be worth checking out.
 
Rob Anybody said:
Hi Chris
Had a 1.8 FL that would cut out ocassionlly, would also sometimes 'hunt' slightly on tickover. eventually a mechanic noticed that diagnostics showed the second lamda sensor giving a very constant reading (1st sensor reading was fluctuating normally) Tickover hunting was being caused by the engine managment system switching beween lean & rich (presumably because it was getting a false reading from the 2nd lamda sensor) Changed 2nd lamda sensor, car ran ok afterwards, tickover more even & didn't cutout again.
Might be worth checking out.
Click to expand...

Not sure you've been told the truth there! The first lambda (pre cat) looks for O2 in the exhaust gas, if it sees some it richens it up if it doesn't it leans it off. It constantly runs rich lean rich lean which gives a fluctuating voltage, this is correct operation! The second lambda (after cat) again looks for oxygen but there should be none coming thu the cat so it should give a pretty constant reading, it's to check the system is working!
 
Diesel Do said:
Not sure you've been told the truth there! The first lambda (pre cat) looks for O2 in the exhaust gas, if it sees some it richens it up if it doesn't it leans it off. It constantly runs rich lean rich lean which gives a fluctuating voltage, this is correct operation! The second lambda (after cat) again looks for oxygen but there should be none coming thu the cat so it should give a pretty constant reading, it's to check the system is working!
Click to expand...

How constant is 'pretty constant' the one on ours was not fluctuating at all, at any engine speed. As I said once I fitted the new sensor it ran better and no longer cut out on us. If the 2nd sensor is giving an incorrect reading would the engine management system adjust the fuelling etc to try and get the reading correct?
 
That ones not really there for fuelling it's more fore checking the system works! The first one is for fuelling! Readings taken after the cat aren't much use to the ECU cos the gasses are changed by the cat, if it thinks the emissions system is faulty it may put it to a preset map to protect the cat from damage? In which case it could make it run rough
 
Diesel Do said:
That ones not really there for fuelling it's more fore checking the system works! The first one is for fuelling! Readings taken after the cat aren't much use to the ECU cos the gasses are changed by the cat, if it thinks the emissions system is faulty it may put it to a preset map to protect the cat from damage? In which case it could make it run rough
Click to expand...

Ok, well thought it was worth posting as it seemed to sort ours
 
Diesel Do said:
Not saying it won't make a difference, every system has its quirks, just that I think you were mislead as to what the two sensors actually do:)
Click to expand...

Ah.. I was not told what the sensors actually did or controlled. I was shown the static reading of the 2nd sensor on the diagnostic equipment when it was connected to the car and as the tickover settled down a bit after I changed the sensor I presumed (as I said in my 1st post) that changing the sensor had also improved the tickover:)
Prehaps should also say that the sensor was a pattern part fitted after someone damaged it trying to pinch the cat, the one I fitted was a genuine LR one
 
If it was flat lining at an unexpected voltage it may well put it into a preset map which cos it hasn't then got fine control, may make it mess around!
 
Does the engine run fine until its warm? if so it could be the IACV - Idle air control valve playing up, it allows extra air into the engine when cold but closes as the engine warms, if it fails in the open position then the car can run rough and cut out.
 
Hi Mantamad

Correct, the engine works great when cold, just when it gets hot the engine just starts to jerk/miss fire and then cuts out !!
 
You must log in or register to reply here.

Similar threads

J
Freelander 1 advice
2
Replies
20
Views
2K
htr
htr
S
Freelander 1 Freelander 1 starts at low rpm then turns off?
Replies
4
Views
333
Arctic2
Arctic2
J
Advice on upgrading
Replies
2
Views
704
KV6-cam
K
landyzoner
Freelander 2 in petrol any good?
Replies
10
Views
1K
RealBeale
RealBeale
J
Freelander 1.8
Replies
3
Views
1K
Nodge68
Nodge68
Back
Top