Disco 3 (LR3) Help!! Discovery 3 will not move

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
newbielandy said:
Will check this tomoz.

Also when you put it from reverse to park it’s o worries making a grinding noise like the shaft is spinning.
Click to expand...
no worries, just hope there’s something there that’s useful

ref the grinding sound I wonder if a driveshaft or Propshaft splines etc has snapped/ have heard a few instances where the transfer gearbox gets stuck into neutral , but of off could keep guessing till the cows come home

at least tomorrow once someone has looked over it and plugged a scanner in will be in a far better potion of what’s going on

indeed plse let us know how u get on
 
Need the codes read as its the 4.4 petrol V8 we can rule out an engine issue.
It's transmission or steering related do I understand correctly the lower control arms were replace then an alignment was done ?? If so was the steering angle sensor reset ?? Many places are unaware this needs to be carried out and in tight tolerance mode to boot.
 
biketeacherdave said:
Need the codes read as its the 4.4 petrol V8 we can rule out an engine issue.
It's transmission or steering related do I understand correctly the lower control arms were replace then an alignment was done ?? If so was the steering angle sensor reset ?? Many places are unaware this needs to be carried out and in tight tolerance mode to boot.
Click to expand...

hi mate

funny enough also thought that with regards to the steering wheel angle sensor , but then when the op mentioned a grinding noise if one of the driveshafts / propshafts have gone ??

also if that happened if the transfer box has got confused due to loosing drive on a CV joint and therefore lost all traction ??

must confess I’m not knowledgeable enough but does make sense if one of them has let go whilst turning a corner ??
 
johnlad said:
I had similar in my D3 when front cv went. It would only move in reverse
Click to expand...

many thks for verifying that as to be honest I wasn’t 100% sure of how it would act with a broken CV joint , particularly with regards to the transfer box showing the green low light

one thought was if the transfer box had gone into neutral for some reason but does make a lot more sense u saying that

many thks
 
johnlad said:
the cv when broke, gives a gearbox speed sensor fault
Click to expand...

many thks, with u saying that wonder if the CDL also gets extremely confused,

also reminded me of when my rear half shaft snapped on my old series 3 , but managed to drive home after locking the FWH in and 4WD , steering was terrible driving it like that , lol
 
biketeacherdave said:
Need the codes read as its the 4.4 petrol V8 we can rule out an engine issue.
It's transmission or steering related do I understand correctly the lower control arms were replace then an alignment was done ?? If so was the steering angle sensor reset ?? Many places are unaware this needs to be carried out and in tight tolerance mode to boot.
Click to expand...
The wheel alignment was done at a local tyre place. Unsure whether the angle sensor was reset.
biketeacherdave said:
Need the codes read as its the 4.4 petrol V8 we can rule out an engine issue.
It's transmission or steering related do I understand correctly the lower control arms were replace then an alignment was done ?? If so was the steering angle sensor reset ?? Many places are unaware this needs to be carried out and in tight tolerance mode to boot.
Click to expand...
The alignment was done at a local tyre place but im unsure whether theyve reset the steering angle sensor. Interesting point there.
 
1988smithy said:
@marjon you might be onto something

Surely the garage would've checked propshafts and cv joints even with it on the ground??
Click to expand...

Plus , credit due where credit is due as @marjon :vb-award::vb-award: beat me to it, lol,

I only wondered about a broken CV/ prop after the OP mentioning about a grinding sound with no drive , at first I wondered as the green low transfer box light showing if for some reason the transfer box was in neutral

fingers crossed is a simple fix for the OP and indeed will know more once a garage has had a look at it
 
biketeacherdave said:
When my steering angle sensor went wrong it put the abs on the offside front wheel causing a grinding noise as you can imagine when trying to drive with a brake caliper on.
Click to expand...


also so refreshing not to have the crank come into this equation seeing it’s a 4.4

pa, think by next year there will be a few more 4.4 joining the anti ULEZ gang lol
 
gstuart said:
Plus , credit due where credit is due as @marjon :vb-award::vb-award: beat me to it, lol,

I only wondered about a broken CV/ prop after the OP mentioning about a grinding sound with no drive , at first I wondered as the green low transfer box light showing if for some reason the transfer box was in neutral
Click to expand...
Can the hi/lo switch fail? Or is there a mechanical bit to it that breaks? Hoping it's something daft for op, I'd love to go and plug my icarsoft in and crawl under it but I'm down in Walsall
 
1988smithy said:
Can the hi/lo switch fail? Or is there a mechanical bit to it that breaks? Hoping it's something daft for op, I'd love to go and plug my icarsoft in and crawl under it but I'm down in Walsall
Click to expand...
This was the first reply on the discovery page apparently they can seize.
 
You must log in or register to reply here.

Similar threads

PieterLV
D2 V8 not starting
Replies
6
Views
432
PieterLV
PieterLV
M
EPB Failure
Replies
0
Views
73
Markdornan1
M
M
Rear Tailgate on landrover disc 3 2008 TDV6 will not open
Replies
3
Views
710
Moggytom
M
J
Discovery 2 td5 failed r9 to fuel pump
Replies
11
Views
1K
Jambo2301
J
Andrewoldold
M&S lights no crank / potentially immobilised?
Replies
1
Views
224
sierrafery
sierrafery
Back
Top