Glueing Plastic clips to door glass

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
W

Windy Rush

New Member
Posts
3
Location
High Wycombe
Hi! I am fitting new glass to my Defender Td5’s passenger door and need to fit the plastic clips to the bottom. I tried it today with one super strength industrial fix it all glue and gave it longer than the stipulated time to cure. Reassembled the door and it worked great until I lowered the window the second time, at which both clips slid elegantly off the glass.

I’ve searched loads of forums etc but this doesn’t seem to be addressed, so I would be very grateful for any of your views on what has worked well in the past to bond these plastic clips to the glass. Many thanks.
 
I used ordinary silicon to bond mine. The weight of the glass alone should be enough to hold it in place. I also fitted new runners in the frame and it's more snug than it was before. My only mistake was fitting the glass carrier slightly off. It now tilts forward and out of the rear vertical runner. No problem when stationary, but if you try to wind the window up while driving, the difference in pressure between inside and out makes the front of the glass to not quite slip into the runner at the top.
 
Thanks Mick. I did wonder about just using silicone. The runners are in pretty good condition but there is just a bit of resistance as the glass moves, which is why it’s weight alone wasn’t quite enough. I’m wondering whether there’s still a little bit of the old broken glass still behind the felt that needs cleaning out. I’ll have another good clean tomorrow and try a good dose of silicone.

Thanks for your help.
 
Am about to start this process as some scroat broke my window to steal the dashcam… is it obvious where the tabs need glueing, is there a diagram somewhere or do I need to take the other door card off on other side to see where the glue tabs go? I was going to use epoxy
 
cborrman said:
Am about to start this process as some scroat broke my window to steal the dashcam… is it obvious where the tabs need glueing, is there a diagram somewhere or do I need to take the other door card off on other side to see where the glue tabs go? I was going to use epoxy
Click to expand...
Wouldn't hurt to take the other door card off, then when all done you can refresh the grease on that side as well, and just for shits and giggles you could spray some rustproofer in there as well. You can see why a 2 hour job takes me a full day.:oops::oops:
 
that’s what I am worried about, be a whole other day taking the other door card off ;)
frog hopper said:
Wouldn't hurt to take the other door card off, then when all done you can refresh the grease on that side as well, and just for shits and giggles you could spray some rustproofer in there as well. You can see why a 2 hour job takes me a full day.:oops::oops:
Click to expand...
 
mick the builder said:
I used ordinary silicon to bond mine. The weight of the glass alone should be enough to hold it in place. I also fitted new runners in the frame and it's more snug than it was before. My only mistake was fitting the glass carrier slightly off. It now tilts forward and out of the rear vertical runner. No problem when stationary, but if you try to wind the window up while driving, the difference in pressure between inside and out makes the front of the glass to not quite slip into the runner at the top.
Click to expand...
yeah I did that the first time, the glue has now come off in the recent silly heat, how do you make sure it's not off second time round?
 
You must log in or register to reply here.

Similar threads

E
P38A Front door glass seperated
Replies
6
Views
1K
Rubberknees
Rubberknees
L
PLASTIC TRIM PANEL REPAIR METHOD
Replies
1
Views
506
Stanleysteamer
Stanleysteamer
Rubberknees
P38 rear door window trims replacement
Replies
14
Views
1K
Rubberknees
Rubberknees
new to all this
New front door
Replies
4
Views
1K
neilp1
N
Shippers
Need to glue glass to glass...
2
Replies
27
Views
2K
Shippers
Shippers
Back
Top