Series 3 Gearbox oil change top cover?

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Neil ... the back wheels mate .. so the prop shaft to the rear diff turns.... in neutral so you can see (hear) if there is anything catching or out of line with the rear drive
 
Ok , I've lifted one of the back wheels and when turned the diff makes a bit of a scraping noise but nothing like when I drive , I might try and remove propshaft tomorrow just to check , betting bolts are seized but heres hoping
 
Ok , I've just noticed something underneath , the red gear shift is really loose and is just clearing the prop so I'll investigate further , I assuming it's not meant to be loose , it's still attached by a bolt but it wobbles all over the place, and I mean all over the place , I'll attach a video when Ava , thanks although it doesn't seem to be catching I wondered if this gave any clues ? I'm not ignoring your suggestions but daylight hours and work are restricting me at moment , thanks
 
it is quite close , was changing the mud cover a few weeks back , its slack in the round hole and on mine the bottom bolt through the clevis bracket thing was well worn still need to order a new one, the nut on the shaft end could be loose, or worn ring/shaft or bottom fixing like mine, shouldnt hit prop though
IMG_5750.JPG
IMG_5753.JPG
IMG_5753.JPG
 
Thanks for that , mine is totally different and really loose at the bottom , the same as the one on the right hand side of the diagram
Screenshot_20190106-213342.png
I
 
Yup that’s the same as mine too , just doesn’t show the forked Clevis thing at the bottom which on mine is very loose , at least the mud won’t jam it ;)
 
Just a final question before I start investigating further , doesn't the fact that the noise is obvious in 1st , 2nd and 3rd and disappears in 4th rule out that it is something hitting the propshaft , I would love to think that it is just something hitting underneath , however due to this fact it sounds unlikely.

Any thoughts?
 
That does sound more like a layshaft fault, its under load in 1, 2 ,3 and not in 4th. As the gears are helical it means that under load = end thrust so load equates to axial force on the shaft bearings.
 
Ok , took out sump plug , a few fine bits of metal and this strange clip. Can anyone identify it please ? , I've put it back together in the second picture it's about 1.5 inch long , and the two ends are bent to a right angle
 

Attachments

  • IMG_20190113_155944882.jpg
    IMG_20190113_155944882.jpg
    167.4 KB · Views: 111
  • IMG_20190113_163400882.jpg
    IMG_20190113_163400882.jpg
    191.5 KB · Views: 154
Last edited:
Ok , done a bit of research , appears to be a synchro clip , there's a rumour this can be replaced without removing the gearbox , does anyone have any knowledge of this ?
 
I can’t recall specific noises on mine when a spring was missing just the crunch if changing too quick,
Is gearbox removal and strip down an option for you, if the other two are still in place I guess it could go for. Along time as normal
 
I'm thinking of refilling oil to be honest and initially seeing if the noise has gone , if it has , I might be able to cope for a while , there was very little oil in gearbox so a full box might help also , I'll give it a go and see , thanks
 
My syncro springs flaied like that but I didn't realise, grears got crunchy but it was overloading the gear teeth, a couple came off and went into the first motion mesh. Had to be recovered 110 miles and then had to replace 3/4 syncho plus 3rd plus the first motion gears that got mangled. I would strongly suggest fixing the springs!
 
You must log in or register to reply here.

Similar threads

C
Gearbox fragments
2
Replies
25
Views
2K
Chonker
C
D
2004 TD4 Gearbox oil change Filler Plug
Replies
6
Views
248
davidnortoni
D
C
Gearbox selector rods
Replies
11
Views
725
steve2286w
steve2286w
Ekenoos
Oil filter parts not mentioned
Replies
10
Views
593
Ekenoos
Ekenoos
S
Timing cover oil seal replacement
Replies
2
Views
684
sprie
S
Back
Top