fuel pump

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Smc33

Smc33

New Member
Posts
32
Do I need to remove the fuel tank on a 04 TD5 to change the in tank fuel pump or is there an inspection cover in the floor?

Thank you
 
Ok thanks, I was trying to find something on here but didn't have any luck
 
If you have the seven-seater, remove the seat trims in the boot floor and cut between the top or the bottom of the cut-outs, that will give you a flap to lift and get at the access plate. Don't cut both ends, just the one is enough.

Peter
 
listerdiesel said:
If you have the seven-seater, remove the seat trims in the boot floor and cut between the top or the bottom of the cut-outs, that will give you a flap to lift and get at the access plate. Don't cut both ends, just the one is enough.

Peter
Click to expand...


Do u mean where the seat fastens down on the floor? How much space is there between the floor and the tank?
 
Yes where the 3rd seats lock into the floor, if you have 3rd row seats.
I have just been out and took a few pictures of mine for you :)
Measurements where 55.5cm from the inside of the black trim, as show in the picture. And it's 38cm from each side of the car. :) image.jpg
 
L90 BCM said:
Yes where the 3rd seats lock into the floor, if you have 3rd row seats.

I have just been out and took a few pictures of mine for you :)

Measurements where 55.5cm from the inside of the black trim, as show in the picture. And it's 38cm from each side of the car. :)View attachment 58617
Click to expand...


Thanks, not sure if I have the ⚽️⚾️🎾 to cut the floor away, will have a look
 
Smc33 said:
Thanks, not sure if I have the ⚽️⚾️�� to cut the floor away, will have a look
Click to expand...

I don't see why you need to cut the carpet, I did ours without resorting to the Stanley knife, and I know another chap who has too.

You do need to remove the carpet trim just inside the rear door, one of the boot mounted seats and the rigid plastic panel behind though.
 
Think it's the difference between an hours job and a 3 hour job, doing it the correct way as per rave.
 
GDM said:
I don't see why you need to cut the carpet, I did ours without resorting to the Stanley knife, and I know another chap who has too.

You do need to remove the carpet trim just inside the rear door, one of the boot mounted seats and the rigid plastic panel behind though.
Click to expand...

cutting the carpet properly is making the job that much easier and quicker,plus it will be hidden anyway.
 
Ok thank you folks, will try and get carpet up and if not will get the knife out, thanks
 
Job done, managed to get carpet up and get it changed, had a bit of difficulty getting the new pump in and to sit right but got there. Thank you
 
It help, when fitting a new pump, to position the rubber seal on the lip of the fuel tank first, then install the pum, then the locking ring.....

After much swearing, I rang a friend for advice and the pump & locking ring were fitted in minutes after that!! :doh: :D
 
DIFFLOCK66 said:
It help, when fitting a new pump, to position the rubber seal on the lip of the fuel tank first, then install the pum, then the locking ring.....



After much swearing, I rang a friend for advice and the pump & locking ring were fitted in minutes after that!! :doh: :D
Click to expand...


Yes I discovered that, could have done with a 3rd hand....got there in the end although I'm not convinced the fuel gauge is working correctly 😥
 
You must log in or register to reply here.

Similar threads

G
TD5 Noisy fuel pump
Replies
3
Views
295
Anaconda
A
J
Discovery 2 td5 failed r9 to fuel pump
Replies
11
Views
1K
Jambo2301
J
D
Disco 2 td5 fuel purging doesn't work?
Replies
10
Views
591
Kev12
Kev12
mad85
Disco 2 TD5 Low Fuel pressure!!
2
Replies
22
Views
621
mad85
mad85
C
Fuel gauge reading
Replies
5
Views
519
tilly2
T
Back
Top