Front Runner Bonnet Mount Spare Wheel TD5

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Hi, I'm looking to mount my spare on the bonnet of my 300tdi 110. Can't find a decent mounting kit for a decent price anywhere!! Any pics would be great to see. Where can you get one for £100??
 
Yep that's the one. None in Europe currently though apparently according to Front Runner. I'm just nervous about impact on a flimsy TD5 bonnet.
 
Lewis07 said:
£100
Click to expand...

Why would you want to spend £100 ? You could make one fairly easily out of a steel wheel rim from a car. Split the rim in two and trim off the part that holds the tyre bead in place so the remainder of the rim will fit inside your spare wheel. Drill it around the edge so that you can bolt it to the bonnet. with adequate re-inforcing on the underside of the bonnet. Weld 3 long bolts to the cut down rim so that they line up with 3 stud holes in your spare wheel.
Cut a steel plate to go under the nuts that you will fit to hold the wheel onto the new mounting.
While you have the welder handy, weld a bar or steel loop on the mounting to take a padlock. Fit 4 suitable rubber pads on the bonnet, spaced out so they will support the spare wheel on the side of it's tyre.
Or......if you are lucky enough to source a scrap Series II or III deluxe dished bonnet complete with it's spare wheel mount, you could fit that mounting. I had one of these on my Series III.
Before you even start, have you driven a Land Rover with a bonnet mounted wheel ? If not, try placing your spare wheel on the bonnet now so that you can get an idea of what it's like to lift a wheel on and off: and also to see how much it might restrict your vision. And remember whenever you open the bonnet.... you will be lifting the spare wheel as well !
Hope this is helpful to you and good luck with it.
 
I would be a bit wary of fitting bonnet spare on TD5 , as they were not an option due to engine , bonnet clearance AFAIK
 
LifetimeLandy said:
Why would you want to spend £100 ? You could make one fairly easily out of a steel wheel rim from a car. Split the rim in two and trim off the part that holds the tyre bead in place so the remainder of the rim will fit inside your spare wheel. Drill it around the edge so that you can bolt it to the bonnet. with adequate re-inforcing on the underside of the bonnet. Weld 3 long bolts to the cut down rim so that they line up with 3 stud holes in your spare wheel.
Cut a steel plate to go under the nuts that you will fit to hold the wheel onto the new mounting.
While you have the welder handy, weld a bar or steel loop on the mounting to take a padlock. Fit 4 suitable rubber pads on the bonnet, spaced out so they will support the spare wheel on the side of it's tyre.
Or......if you are lucky enough to source a scrap Series II or III deluxe dished bonnet complete with it's spare wheel mount, you could fit that mounting. I had one of these on my Series III.
Before you even start, have you driven a Land Rover with a bonnet mounted wheel ? If not, try placing your spare wheel on the bonnet now so that you can get an idea of what it's like to lift a wheel on and off: and also to see how much it might restrict your vision. And remember whenever you open the bonnet.... you will be lifting the spare wheel as well !
Hope this is helpful to you and good luck with it.
Click to expand...

Haven't the skill for all that I'm sad to say. I have a 90 with a bonnet spare wheel which I had fitted last year (300 TDI) so happy with the practicalities of vision and lifting bonnet.
 
these will work just as well , whichever you use dontforget to brace underbonnet , using a earlier bonnet with it all done is probably easier course, as they sit higher with a td5 because of the hump , repeat my clearance caveat tho .
 
I had a S111 with a bonnet mounted 600 section spare tyre, that was difficult to get on and off, was a pain to lift the bonnet and compromised forward visibility. I really would not want to repeat the exercise with the 235/85/R16 and alloy on my 90.
/
 
from experience a 265/75 is about as wide as you can go on a defender bonnet (dished type) without a view compromise , depending on if you are height challenged :)
 
You lot must be weak as I have a 7.5x16 Michelin xzl on a genuine wolf xd rim and I can both open the bonnet and lift it on and off with no particular problems. And I am a 90kg 6ft normal guy who eats bad and doesn't go to the gym
 
You must log in or register to reply here.

Similar threads

tweedandbriar
Spare wheel...
Replies
5
Views
584
dag019
dag019
Milleme
Landy security....attempted break in
Replies
10
Views
297
Mickob71
Mickob71
T
Spongy(?) Steering
Replies
1
Views
258
tottot
tottot
S
bonnet catch problems
Replies
3
Views
471
sprie
S
B
Metal brake fluid reservoir for Td5
Replies
7
Views
766
Baldgit
B
Back
Top