mutsnutz
Well-Known Member
- Posts
- 1,964
- Location
- pink panther country
how do you remove the front bumper on a p38 1995 diesel please got to take it off due to a dickhead pulling out in front of me and putting the range into some metal railings 
front bumper removal
- Thread starter mutsnutz
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
dave4x4
Active Member
- Posts
- 360
- Location
- Chester, England
Undo a clip either side of the front valance underneath then undo the two bolts under the front bumper and slide it forward.
10 min job unless the bolts haven't been out in 18 years and have rusted in. Then a nightmare.
10 min job unless the bolts haven't been out in 18 years and have rusted in. Then a nightmare.
mutsnutz
Well-Known Member
- Posts
- 1,964
- Location
- pink panther country
cheers mate hope it comes of easy now to find a suitable replacement
now to find a suitable replacement 
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
When you undo the bolts, the bumper should drop a few mm to release the upper locating pegs. It may need a thump on the top surface. It will not pull forward until it drops.
mutsnutz
Well-Known Member
- Posts
- 1,964
- Location
- pink panther country
cheers mate thanks for the tip
kurtjohnson10
Well-Known Member
- Posts
- 15,235
- Location
- midlands
They do sometimes stick as said above so don't be frightened to give it a small thump to loosen it a little ! It's quite an easy job better if two of you on it to hold it!
mutsnutz
Well-Known Member
- Posts
- 1,964
- Location
- pink panther country
just ordered my new bumper should be here next week thanks for the two person tip il pop into my mates garage to do it then he can give me a hand with it
mutsnutz
Well-Known Member
- Posts
- 1,964
- Location
- pink panther country
does anyone know what size socket is it for the bumper bolts please just incase i need to buy one
- Posts
- 58,170
- Location
- Preston Lancs.
Bolts are 10x30 so 17 mm socket. If they are rusty single hex better than bihex.
mutsnutz
Well-Known Member
- Posts
- 1,964
- Location
- pink panther country
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
The bolts on mine had star type torx heads, had to go buy a special spannerthanks very much mate your a star
- Posts
- 58,170
- Location
- Preston Lancs.
The bolts on mine had star type torx heads, had to go buy a special spanner
Yeah they are BMW specials. Have set of sockets for those.
mutsnutz
Well-Known Member
- Posts
- 1,964
- Location
- pink panther country
Yeah they are BMW specials. Have set of sockets for those.
so i need a set of those them
- Posts
- 58,170
- Location
- Preston Lancs.
Have a look and see what you have on your car. If it's 1999 on it will be those. These are what you will need if they are.
14PC CHROME VANADIUM FEMALE TX STAR TORX STAR SOCKET SET ON SOCKETS RAIL E4-E24 | eBay
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
I just bought the one piece.
mutsnutz
Well-Known Member
- Posts
- 1,964
- Location
- pink panther country
its a 1995
- Posts
- 58,170
- Location
- Preston Lancs.
Then it may not have them they are pretty specific to VW, BMW, Audi and Merc. But have a look first.
- Posts
- 58,170
- Location
- Preston Lancs.
mutsnutz
Well-Known Member
- Posts
- 1,964
- Location
- pink panther country
it does have the torx ones so job is now done pretty simple thanks to you all for the help and advice
Taximan2011
New Member
- Posts
- 338
- Location
- Weston Super Mare, N.Somerset
Tried to remove my front bumper today ready to prime it tomorrow. Undone the wire clips each side that locate the plastic profile rail in place undone the two torx bolts and used a rubber mallet but it wouldn't budge an inch. So probably gonna take fogs out and mask up the car and spray it on the car.
Similar threads
