Front Brake Disc

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
K

kapilamuni

Active Member
Posts
550
I need to replace the front brake discs(Min thickness close to 22mm) and part no NTC8780 is not available. Can I put Disco II front disc part no SDB000380, which is available. Dico II s rears are a direct match with P38 rears.
I don't want to remove the disc and take it to compare with Disco one as I might damage it while trying to remove. In that case if it's a no match, I won't be able run the car.
 
Order new disc screws and caliper bolts when you do it. I used a punch to knock the screw round s it was well and truly stuck. Heat might be required on the caliper bolts but watch any rubber parts (boots, flexible hoses etc) nearby.

I wouldn't be surprised if they are the same discs but don't know for sure.
 
Did the rears today. Yes, that screw is a pain. Used the drill and everything fine thereafter.
My rear discs were worn down to 8mm, much below the set limit.
Ordering a pair of front disks is costly and with the weight size shipping will be killing.
Disco II has a different part no for front discs.
 
Guys, is Bearmach a good brand for front discs?
An indie is ready to get a set for me at a reasonable price.
 
kapilamuni said:
Guys, is Bearmach a good brand for front discs?
An indie is ready to get a set for me at a reasonable price.
Click to expand...

What do you regard as reasonable? Look on Ebay there are loads of them. But remember you get what you pay for. And new discs and pads MUST be run in after fitting. No heavy or sustained braking for 250 miles no sitting at lights with foot brake applied or even the dear ones can warp.
 
kapilamuni said:
Guys, is Bearmach a good brand for front discs?
An indie is ready to get a set for me at a reasonable price.
Click to expand...

Eurocarparts usually have an offer code available somewhere and if they don't if you call the head office they usually give you some off. With the discount you can usually get Padgid or Mintex for a similar price to Britpart, although Brembo aren't that much more and the pads might not cause so much dust (I'm hoping). My pads are due for replacement soon so that's what I'll be trying next. My discs should be good for a few more years I hope. Don't know if they ship to Sri Lanka though but might be worth asking.
 
Rimmers want 135GBP to ship two discs. which comes upto 210 GBP in total. Also, on top of that will have to pay import duty on such a heavy item.
The indie agreed to deliver at a total cost around 120 GBP. That is reasonable, I believe.
I want to know whether Bearmach discs stand together with Delphi or with -----part, in an quality perspective.
I understand the run-in process but 'no sitting at lights with foot brake applied..':confused:
 
kapilamuni said:
Rimmers want 135GBP to ship two discs. which comes upto 210 GBP in total. Also, on top of that will have to pay import duty on such a heavy item.
The indie agreed to deliver at a total cost around 120 GBP. That is reasonable, I believe.
I want to know whether Bearmach discs stand together with Delphi or with -----part, in an quality perspective.
I understand the run-in process but 'no sitting at lights with foot brake applied..':confused:
Click to expand...

I tried some Bearmach engine mounts last summer. The studs sheared clean off and when I looked at the second one I could see why. The quality was pretty poor so I put the original mounts back on (they were better than the new Bearmach). I'd say Bearmach are slightly better than ----part but not much in it. Delphi I would go for. Or see if the Indie can get Padgid or Brembo?
 
kapilamuni said:
Rimmers want 135GBP to ship two discs. which comes upto 210 GBP in total. Also, on top of that will have to pay import duty on such a heavy item.
The indie agreed to deliver at a total cost around 120 GBP. That is reasonable, I believe.
I want to know whether Bearmach discs stand together with Delphi or with -----part, in an quality perspective.
I understand the run-in process but 'no sitting at lights with foot brake applied..':confused:
Click to expand...

If the discs and pads are hot after long braking from high speed sitting with the pads in contact with the discs will cause unequal cooling of the discs.
 
Wammers , this is my daily travel . We have heavy traffic here with average speed about 5 Km per hour. Daily about 3 hrs spent on the road to office & back. with the foot is mostly on the brake pedal. :D:D
 
kapilamuni said:
Wammers , this is my daily travel . We have heavy traffic here with average speed about 5 Km per hour. Daily about 3 hrs spent on the road to office & back. with the foot is mostly on the brake pedal. :D:D
Click to expand...

Why change discs and pads then in traffic like that, what you have is good for another twenty or thirty years. :p;)
 
Oh my......
This sin to continue for another 20yrs ? :mad::mad:
Anyway, you should have told me , before I spent money on discs n pads.:oops:
 
You must log in or register to reply here.

Similar threads

G
Defender 110 brake callipers
Replies
5
Views
514
Groaning Hippo
G
kato Disco
Defender with discovery front axle - are the brake components the same?
Replies
11
Views
431
Hicap phill
H
M
Brake fluid leak or not
2
Replies
37
Views
2K
mousemat
M
Graculus
For Sale Assorted L322 parts package
Replies
3
Views
1K
Graculus
Graculus
D
FTC3846 (300TDi solid rear brake disc) – different dimensions between suppliers
Replies
7
Views
2K
djpeanut
D
Back
Top