- Posts
- 1,512
- Location
- Somerset (but I'm a Landanna)
freelander 1
- Thread starter tyrefitter
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Alibro
Well-Known Member
- Posts
- 7,182
- Location
- Northern Ireland
Oi!!! That was my line.I don't like to say I told you so, but I told you so.
Sounds like a plan.
Come back to say how you got on.
Good job spotting the issue but I'd highly recommend you whip the drive shaft off before driving the car any further.
yantojarc
Member
- Posts
- 48
- Location
- South Wales
All booked for Friday to change VCU and bearings. Just as an add on great service at Bell Engineering taking the 2 VCUs I have in part ex for the new one and also put me off buying the beatings from them as they only have the cheap ones in stock. Went to Island 4x4 in the end for the beatings for the GKN ones£50.00 a shot mind you but don't do big milage so should last a while Thanks again.
yantojarc
Member
- Posts
- 48
- Location
- South Wales
Another small issue... Wi ds teen wipers... When on intermittent they stop half way up the screen and then com e back down... The delay is dependent on the setting I.e short or long pause. Is there an easy fix or is it new wiper stalks...?
It's the motor return contact in the motor that is worn. It is repairable, or you can replace the wiper motor.
yantojarc
Member
- Posts
- 48
- Location
- South Wales
All looking good now. But don't know if I'm looking for problems that aren't there but the engine dies seem quite noisy first thing. Not sure if this is just normal diesel engine noise but seems like a Tapping sound. It does seem to go quieter after driving for a few miles. I did an oil change when I first had the car using Castrol Magnatec 10W40, is this the correct oil or is there something better to use or safe additive. Any thoughts would be appriciated.
A 5w40 fully-synthetic is better, than a 10w40 semi-synthetic, in that it's less thick when cold, and protection is better when hot.
yantojarc
Member
- Posts
- 48
- Location
- South Wales
Thanks for this I'll change on the weekend.
yantojarc
Member
- Posts
- 48
- Location
- South Wales
Another question for you Midge 68 or anyone else for that matter. I've unfortunately snapped 2 bolts on the inlet manifold (then found a previous post from you Nodge about how to tighten 
). Any ideas how to remove the snapped bolts and what are the new bolts required. I was wondering if it would be easier to get a new manifold from a breakers yard instead?
). Any ideas how to remove the snapped bolts and what are the new bolts required. I was wondering if it would be easier to get a new manifold from a breakers yard instead?
Madmustang
Well-Known Member
- Posts
- 1,646
- Location
- Castleford
And mine, Another IRD blown!
GrumpyGel
Well-Known Member
- Posts
- 26,390
- Location
- Christchurch, New Zealand
Alibro
Well-Known Member
- Posts
- 7,182
- Location
- Northern Ireland
I have a spare inlet manifold which I think is complete and OK if a bit dirty. Happy to let it go for a tenner plus postage. PM me If your interested.Another question for you Midge 68 or anyone else for that matter. I've unfortunately snapped 2 bolts on the inlet manifold (then found a previous post from you Nodge about how to tighten
It is a TD4 inlet manifold your talking about?
yantojarc
Member
- Posts
- 48
- Location
- South Wales
Thanks Alibro. I've replied PM. I've ordered one of the stud /bolt extraction tools to remove the rest if the stud left behind. Have you used these tools and do you think it will work or is there another easier way?
Not always easily unfortunately. Post some pictures of the offending bolts and surrounding area, so we can take a look.
For reference, the bolts only need "nipping" up, as the sealing is done with O rings. I think the official torque figure is about 18Nm, so not tight at all really.
yantojarc
Member
- Posts
- 48
- Location
- South Wales
I did see a previous post from you, but a bit late. In fairness one bolt was already loose after being snapped and the other snapped when I was undoing it, so not my fault.... This time at least. Just wondering to stop any further damage would it survive with the bolts missing. Can't hear any air being sucked in.
Mine has had a missing nut since I've owned it, it's not really a problem.
Air could leak out, not be sucked in, as the manifold is under pressure when the engine is running.
yantojarc
Member
- Posts
- 48
- Location
- South Wales
I'm glad you mentioned that as I was wondering if I would do more harm than good trying to remove the snapped ones
yantojarc
Member
- Posts
- 48
- Location
- South Wales
Hi thanks for all your help on my previous issues with my TD4. Just wondering if I could pick your brains again. Looks like the Aux belt has snapped and looks like a bigger job than I could handle. With belt snapped can a drive it a few miles to get to the garage or is it a tow truck job?
andyfreelandy
Well-Known Member
- Posts
- 5,563
- Location
- Devon
There will be no power steering, water pump or charge to battery.
Steering dangerously heavy without belt. Changing belt is not a hard job, covered on many a thread with a threading guide too!!
Steering dangerously heavy without belt. Changing belt is not a hard job, covered on many a thread with a threading guide too!!
Similar threads
