engine management light
- Thread starter ste220
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
thanks for offer mate which the pipes that are conncted to th egr valve. i dont see how changing plugs can cause this if all was ok before we started.it would not be because i have 3 different brands of glow plugs in would it ?
ratty
I'm not special I'm limited edition
- Posts
- 34,277
For those that don't know it, code 144 is.....
O2 sensor circuit high voltage (bank 1 sensor3)
O2 sensor circuit high voltage (bank 1 sensor3)
so where do i need to look? thanks p.s, you do realise its an l-series
ratty
I'm not special I'm limited edition
- Posts
- 34,277
The code is a standard obd2 code so it doesn't matter what the engine is. As for where to start looking I don't have a clue to be honest with you. I just looked it up in my magic booklet. I will see what I can find out for you. I just thought that if people knew what code 144 is they might be able to help you further.
ratty
I'm not special I'm limited edition
- Posts
- 34,277
looking at what you posted earlier..
coupled with the standard obd2 code I would say check you haven't dislodged any of the injector wires on the 3rd cylinder.
coupled with the standard obd2 code I would say check you haven't dislodged any of the injector wires on the 3rd cylinder.
ratty
I'm not special I'm limited edition
- Posts
- 34,277
strange????
The misfire and loss of power only comes on at speeds of 45-50mph?
These are only guesses but....
Firstly check your earth straps to your engine are clean and secure. If need be try fitting an additional one. Then take your vehicle on a test drive. Working glow plugs may be putting additional strain on your engines current wiring.
If that doesn't work.....
Find out what revs your engine is doing at 45-50mph. (you may have to drive it while watching the guage)
While stationary attatch a multimeter to your battery. Start your engine and get somebody to hold the revs so they are the same as you would have doing the above speeds.
Does the voltage go above 15v? Does the misfire/ warning light still come on? I am just wondering if the voltage is getting too high and spiking the ecu.
Greenie
New Member
- Posts
- 736
- Location
- River Nene
Just looked at my code listings.. and its the same as wattys..
02 sensor circuit high voltage (bank 1 sensor 3)
So.... What is sensor 3 ??
02 sensor circuit high voltage (bank 1 sensor 3)
So.... What is sensor 3 ??
99 l series
what year is the car? it is probably obd not obd 2
02 sensor circuit is an obd 2 code isn't it and wouldn't apply to an l series diesel.
so the code is likely to be vehicle specific
Chaser
New Member
- Posts
- 2,175
i should make it clear i don't know much about about on board diagnostics but from what i've read pre 2003 diesels were not required to be eobd compliant and as such can have their own fault code systems.
confirm with whoever gave you the definition of 'injection start control' if this is correct for your vehicle and then try to find what it relates to on your vehicle.
sound like it's a circuit relating to injection timing of some sort (camshaft/crankshaft sensor circuits or injectors themselves)
does this happen about a second before the light comes on like mine???? will be the management going into limp mode!
the misfire is the ecu going into limp mode i think!!!! mine happens when sat at a constant throttle for around 10ish seconds!
ratty
I'm not special I'm limited edition
- Posts
- 34,277
You are correct about it being the ECU going into limp mode. It is just the fact it does it only at 45-50mph that is strange. Is it ok above these speeds?
Similar threads
