- Posts
- 12,628
- Location
- Sud ouest France !
Eas program no comms
- Thread starter Rollinthunda
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
Have you cut out the connectors at the base of the A posts behind the plastic kick panels? Cut them out,solder and heat shrink the wires.if you still have no success after doing both sides then PM me, envelope symbol top right with your phone number and we can try my working kit on your car and your kit on mine to make sure it's working.I'm no electrickery eggspert but we'll try.
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Quite right. I live in the sun in Bucks. I used to visit the NW but most of the people I knew are dead now.
- Posts
- 12,628
- Location
- Sud ouest France !
I've no idea why I thought that you were over there, sorry @Grrrrrr - rrrrrr..
Rollinthunda
Member
- Posts
- 39
- Location
- Warrington england
Ok guys yes my set up works on another vehicle (cheers Alan) I have soldered all wires in passenger footwell and still no difference, could there be corrosion in the obd2 that I can’t see?
Rollinthunda
Member
- Posts
- 39
- Location
- Warrington england
Cheers Alan for the help my set up works fine on another vehicle so I’ve soldered all wires in passenger footwell and still same result! Also have orange lift on dash of Rangerover with arrow underneath that has been there since hard fault just not sure I’ve mentioned it
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
Yes, the wires can even corrode off at the back.
I assume that the correct EAS relay is fitted under the passenger seat?
Rollinthunda
Member
- Posts
- 39
- Location
- Warrington england
Rollinthunda
Member
- Posts
- 39
- Location
- Warrington england
Picture in previous post of eas relay
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
That's the one.
Rollinthunda
Member
- Posts
- 39
- Location
- Warrington england
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
Playing around with the Comm port selection in the RSW software, often times you're on the wrong port and it won't connect..
Other times it can be the cable itself Did you put the driver for the USB to serial adaptor into your laptop before you connected it to car. The generic Windows drivers usually don't work, also worth trying to drop the baud rate to 4,800.
Assuming you're using RSW software
Other times it can be the cable itself Did you put the driver for the USB to serial adaptor into your laptop before you connected it to car. The generic Windows drivers usually don't work, also worth trying to drop the baud rate to 4,800.
Assuming you're using RSW software
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
His cable and software work on another car Henry, so the problem is in the car. If the OBD connector change doesn't fix it, I'd be trying a replacement EAS relay followed by the ECU as I have spares.Playing around with the Comm port selection in the RSW software, often times you're on the wrong port and it won't connect..
Other times it can be the cable itself Did you put the driver for the USB to serial adaptor into your laptop before you connected it to car. The generic Windows drivers usually don't work, also worth trying to drop the baud rate to 4,800.
Assuming you're using RSW software
- Posts
- 3,878
- Location
- Near Heathrow.
I know it's been said before, but re-check all the connections to the diagnostic port. EAS needs pins 1 for the timer relay, and pins 11 & 12 for communications. Pins 4, 5 & 16 are always required for Nanocom, but for EAS-Unlock it depends on the cable. Either 4 or 5 will be required for Ground connection.
Remember C104 & C204 are behind LH footwell panel, but C102 & C202 are behind the RH panel.
I agree with Kieth that checking the timer relay is a good idea, because without this you cannot start diagnostics. My understanding is the ECU needs the relay to be toggled to force a reboot, because EAS-Unlock sends a special sequence when the ECU powers on to start the diagnostic mode. This why you get the warning beeps when EAS diagnostic starts.
Pete
Remember C104 & C204 are behind LH footwell panel, but C102 & C202 are behind the RH panel.
I agree with Kieth that checking the timer relay is a good idea, because without this you cannot start diagnostics. My understanding is the ECU needs the relay to be toggled to force a reboot, because EAS-Unlock sends a special sequence when the ECU powers on to start the diagnostic mode. This why you get the warning beeps when EAS diagnostic starts.
Pete
Last edited:
Rollinthunda
Member
- Posts
- 39
- Location
- Warrington england
Rollinthunda
Member
- Posts
- 39
- Location
- Warrington england
I can definitely hear something clicking under passenger seat obvs got to be the relay still getting pp in the rx also what or where is the baud rate if you mean the sliders for idle delay they only go from 0-500
Last edited:
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
Change the under seat EAS relay as your next step. Not expensive secondhand.
Rollinthunda
Member
- Posts
- 39
- Location
- Warrington england
Mine clicks when you initialise program and then a sec or 2 later clicks again. Bare in mind the car was totally fine until the catastrophic air leak! I’m not keen on buying a 2nd hand relay when mine appears to be ok and for all I know the 2nd hand one could be buggered. I am definitely at a dead end now. I feel like torching it but the can of petrol is too expensive
Last edited:
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
Do you get the beeps and the Slow 35mph message when you plug in the EAS cable from the computer?
If the relay doesn't operate correctly, there will be no comms, I assume it's a tall black relay?
