I have a p38 auto diesel y ref 2001. I have a hard eas fault. I’ve unlocked it with eas reset software but it’s still not right. In the last year I’ve changed the eas pump it had when I bought it and have since put two more new pumps in. I’ve changed the front air bags and the rears look new as well. I’ve also changed the seals on the valve block. I’ve even changed the eas ecu .Since changing the seals on the valve block it’s never dropped over night even when left for a week. I’m 100% certain there are no leaks anywhere. Help please I dont know where to go next.
EAS help!!
- Thread starter Wayne890
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
If the pumps keep failing, there is a leak. If the bags are good and it doesn't drop, the a leak on the storage side is a possibility.
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
The line to the air tank or the tank itself, or the air dryer.
You don't say what fault is reported by the EAS software, if it's "Vehicle has moved" it can be ignored.
brianp38dse
Well-Known Member
- Posts
- 20,065
- Location
- heathrow
We have had quite a few people with pin holes in the pipe that runs to the tank caused by exhaust leaks, cheep enough to replace pipe to rule it out.
but as Datatek said its feeding a leak some ware.
but as Datatek said its feeding a leak some ware.
tarphenry
Well-Known Member
- Posts
- 1,540
- Location
- bury lancs
I had a lot of trouble with mine and anew set of NRValves seem to have solved the troubles.
Tenebreaux
Well-Known Member
- Posts
- 4,303
- Location
- Armagh
Can I ask where you got the NRVs? I've never seen them for sale separately.
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Try asking Kurt.
tarphenry
Well-Known Member
- Posts
- 1,540
- Location
- bury lancs
I got mine from Kurt and until you see new ones, you dont appreciate how worn the old ones are
Jon Dor
Well-Known Member
- Posts
- 1,672
- Location
- Beverley, East Riding of Yorkshire
I'm hoping that replacing the lot will be a good investment.
- Posts
- 2,101
- Location
- Mull of Kintyre
If no height loss I agree leak is on storage side but it depends on what diagnostics says the fault is
I have vehicle has moved and rr valve stuck closed
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
"Vehicle has moved" can be ignored. RR valve stuck closed could be a height sensor as if when the ECU commands the valve to open no movement is detected, the ECU will assume the valve has not opened.
Could be the connector the the sensor is corroded, could also be the connectors in the EAS box.
- Posts
- 58,170
- Location
- Preston Lancs.
First one is correct second one has bad comms.
I’m in access mode now but won’t lift any higher a quick drive round the block and feels like rear right side is not getting to height. So I think I’ll start by getting that wheel off and having a look around there. I’ve had about 6 months of faultless operation which is why I’m sceptical there is a leak? This is exactly what happened last time and after changing the ecu everything was fine
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
The ECU's rarely fail, corroded connections and duff height sensors are common.
Yes it’s odd though that changing the ecu was an immediate fix and now it’s doing the same. Fault with the connection to the ecu on the car side maybe?
Datatek
Well-Known Member
- Posts
- 44,887
- Location
- Near Poitiers SW France
As I said, corrosion on connectors is a common problem though not so often on the ECU connector itself.
