DT engine knocking

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
H

hlaverty

Member
Posts
37
Location
Livingston, Scotland
Ok, Got the P38 2.5 DT (203k miles R reg) so far it has run as expected (slowly doing approx. 700 motorway miles a week) since I got it, it has been difficult to start, I went out the other morning and it was turning over but refusing to start (getting just about there but not quite) and ran the battery down , so charged it up and eventually, after a fair bit of turning over it started, but there is now a knocking from the engine it reminds me of knackered big end bearings but coming from the top end and louder towards the front, this 'knocking' goes away at 1250 revs and it then just sounds like a normal diesel engine (well as normal as a 2.5 DT will get) also the knocking doesn't get any faster as the revs increase to 1250, I had already glow plugs so when they arrived I fitted them and now the car starts a whole lot better (but still the knocking) and, being the brave (stupid) sole that I am took it for a thirty mile run, where it drove as it usually does (slowly but gets your there) but knocking still there (a lot quieter with the bonnet down) any 2.5 diesel experts out there got any ideas?
 
Whats your oil pressure like? I'm no expert but id look there to start with. An oil pump failing/on its last legs may well not be getting much oil to the top end...??


Just a thought
 
Update, went out and released the tension on the auxiliary belt (alternator), and the noise goes away (aux belt starts slipping), so it is not the engine itself but something that is connected through the auxiliary belt
 
When crank pulley is on it's way out it knocks only when there is load on it on low revs. Its simply dual mass pulley(harmonic balancer), no need for it when spinning fast, hence why it smoothens on higher revs.
 
N2O said:
When crank pulley is on it's way out it knocks only when there is load on it on low revs. Its simply dual mass pulley(harmonic balancer), no need for it when spinning fast, hence why it smoothens on higher revs.
Click to expand...

Don't want to get into a ****ing contest with you but when my mates started to break up the car was undriveable. Guess the op has to check everything that drives or is driven by the belt.:)
 
There is a possibility that the tension idler is fouling the the plate on the crank pulley.

When I refurbished my engine I started it up and the new tension Idler was just catching the plate and creating the most awful noise, from memory there are three or four raised castings on the crank pulley plate and these were bashing the tension idler.

It was a new part so I had a machine shop mill and few millimetres off it which solved the issue

Maybe your tension idler is tired and has developed play and is catching the plate as they over lap and there is a fairly close tolerance between them.

Worth a shot
 
If the rubber separating the inner and outer is knackered the inner parts retention fingers could be striking the outer part causing a knock. But the torsional damper would have to be pretty well goosed for that to happen.
 
tomcat59alan said:
Not when referring to crankshaft pulleys Tony.:rolleyes::D:D:D. In his original post he said the knocking is coming from the top end of the engine. You been busy this weekend ? not to many posts.:)
Click to expand...

Not specially busy just doing other things. Yeah the crank pulley is hardly the top of the engine. Maybe a sick tappet. But the crank pulley inner has three fingers on it that fit in slots in the outer. Basically so if the rubber between them becomes detached it cannot spin inside the inner and cause loss of drive. They can rattle about a bit i suppose if totally goosed. This may cause the tensioner to oscillate somewhat though, that would give a visual indication of damper on it's way out. You do get a gentle movement of the tensioner with a good pulley but with a duff pulley it would be very noticeable and rapid. :);)
 
You must log in or register to reply here.

Similar threads

N
Engine knocking sounds
Replies
9
Views
828
Mark Piercy
Mark Piercy
M
L322 3.0 2006 Vogue droning noise at 30mph and above
Replies
9
Views
842
pwood999
pwood999
Paul Coddington
P38A Viscous coupling
Replies
14
Views
607
Mark Piercy
Mark Piercy
MalcolminSpain
Horrible noise
Replies
2
Views
847
MalcolminSpain
MalcolminSpain
L
L405 Knocking noise
Replies
6
Views
2K
gstuart
gstuart
Back
Top