doriz
Well-Known Member
- Posts
- 17,312
So I've just been out for a poke about. The cap is perished, however, if you squeeze it the grease oozes out
Doriz CSW
- Thread starter doriz
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
So I've just been out for a poke about. The cap is perished, however, if you squeeze it the grease oozes out
Hicap phill
Well-Known Member
- Posts
- 16,237
- Location
- Wiltshire
Did you replace the circlip on the end of the drive shaft?
Caps are easy to replace
Caps are easy to replace
doriz
Well-Known Member
- Posts
- 17,312
I have never been near the hubs as yet, its on my list. I have ordered a new cap, so when it arrives I'll check the integrity of the circlip.
Last edited:
doriz
Well-Known Member
- Posts
- 17,312
I have the part to do the tappets - Question, when I replace the rocker gasket do I need anything to seat it like instant gasket sealer or will it just press home?
Hicap phill
Well-Known Member
- Posts
- 16,237
- Location
- Wiltshire
I do put a smear of clear hylomor each side of the gasket just so it does not move when replacing the cover. Dont need to much.
Don’t forget it’s the rule of nine
Don’t forget it’s the rule of nine
- Posts
- 68,223
- Location
- The Wooly Witch
In desperate straits been known to use a dab of grease ....
doriz
Well-Known Member
- Posts
- 17,312
Is that 9x9 is 81?
- Posts
- 68,223
- Location
- The Wooly Witch
No, silly, it's a 9 inch rule .... you know... you were twanging the rule on the desk and it snapped ....
doriz
Well-Known Member
- Posts
- 17,312
doriz
Well-Known Member
- Posts
- 17,312
I'm in the market for some sill checker - anyone advise me what size (large flange) pop rivets I will need please?
Hicap phill
Well-Known Member
- Posts
- 16,237
- Location
- Wiltshire
Should be normal 6mm rivets as the checker plate Is countersunk.
doriz
Well-Known Member
- Posts
- 17,312
I'm going to do the cam belt next week...whilst everything is in bits I will do the water pump, thermostat, belts, the radiator change and hoses - can you think of anything else I should do whilst going deep?
doriz
Well-Known Member
- Posts
- 17,312
VIN question from my 110 if I may?
Looking at the Rimmer catalogue etc for part numbers I’m directed to the VIN. Anyhoo I look at the engine plate and it don’t match the V5C
Anyhoo, after digging off the wax oil the chassis VIN, engine plate and engine all match. The discrepancy Is the 6th letter, on the V5C shows a ‘B’ which isn’t even listed in the descriptors the Car shows an ‘M’ for 110. Can I simply send this to DVLA (change vehicle details) as it looks like an input error at some point, or should I blast it with pizz .
The unique serial (last 6) match on everything.
Looking at the Rimmer catalogue etc for part numbers I’m directed to the VIN. Anyhoo I look at the engine plate and it don’t match the V5C
Anyhoo, after digging off the wax oil the chassis VIN, engine plate and engine all match. The discrepancy Is the 6th letter, on the V5C shows a ‘B’ which isn’t even listed in the descriptors the Car shows an ‘M’ for 110. Can I simply send this to DVLA (change vehicle details) as it looks like an input error at some point, or should I blast it with pizz .
The unique serial (last 6) match on everything.
Send it to DVLA just fill in the correct number in the change section and add a covering letter to explain its a 110 so should be 'M'
I changed the frame number on my bike recently it was because they had mixed up the last 3 digits Had to chase them with a couple of phone calls but no issue.
Also changed engine number and CC in the overfinch so it was correct also no issues
Much better to have all numbers right this day and age
J
I changed the frame number on my bike recently it was because they had mixed up the last 3 digits
Had to chase them with a couple of phone calls but no issue.Also changed engine number and CC in the overfinch so it was correct also no issues
Much better to have all numbers right this day and age
J
doriz
Well-Known Member
- Posts
- 17,312
Radiator part number please... Bearmach all metal affair. BTP1823 (R) apparently doesn’t fit a 1991 200 TDI @jamesmartin @Hicap phill
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
its the right number only the oil cooler connections might differ due to year,ive had to change those fittings in the past to suitRadiator part number please... Bearmach all metal affair. BTP1823 (R) apparently doesn’t fit a 1991 200 TDI @jamesmartin @Hicap phill
doriz
Well-Known Member
- Posts
- 17,312
I think the Bearmach comes with adaptors for the oil cooler. Cheers @jamesmartin
doriz
Well-Known Member
- Posts
- 17,312
I have a leak at the rear where the hardtop to body foam seal has perished or gone hard. Is it possible to loosen the fixings to create enough space to fit a new seal or does the panel need to come out which will affect other seals like upper panel to roof seal?
- Posts
- 10,368
- Location
- A bit sarf of Dorking
I've only ever taken the sides off or on while the roof was off, but on a 110 I think you'd be lucky to force enough of a gap at the front, especially since the roof seals are probably just as fragile as the body/sides ones. With a 90 (and no B or C post) you'd probably have got away with it.
I think you'd be best to wait for summer and do it properly....
doriz
Well-Known Member
- Posts
- 17,312
Grrrrrr
