Disco1 rear quarter removal - help

Chrisw8 · Apr 22, 2015

Getting my o/s rear quarter off ....

Are these rivets? And do they need to be drilled out to get panel off?

I've undone screws and bolts and cut through sticky stuff but I am stuck at this point.

Any body help ?

Chrisw8 · Apr 22, 2015

Oooooo , and how do I get over the fuel filler..... Does it just pop off???

Chrisw8 · Apr 22, 2015

right. home now, just been searching.

looks like I'll need to disconnect fuel pipe from under car.

Anyone know about those rivets ??

sam7986 · Apr 22, 2015

They certainly look like rivets; that being the case whack the head off the rivet with a sharp flat blade/chisel and jobs a good'un!

MGBGTV8 · Apr 23, 2015

Yes, they are rivets. You'll need to drill those out.

Be REALLY gentle when you do this job if you want to reuse the panel. Start at the door end and work your way backwards towards the rear of the car.
There are shed loads of bolts inside and a couple hiding in the wheel arch.
There are also a few self tappers to wind out which you'll spot when you open the tailgate.
You should also remove the rear E post speaker as you'll need to drill out two rivets holding that bracket onto the car.

Chrisw8 · Apr 23, 2015

Hi MGB.....

I've found all the screws and bolts, it was the rivets that threw me. Thanks for info, Ill drill them out next time im working on it early next week and post the piccies in my main thread.

Alantoo · Apr 25, 2015

Yes rivets, drilling the heads off will be less likely to damage than a chisel.

I have posted some photos on the rear quarter sealant thread which may help.

I still ended up twisting the hose clamps off to remove them even after wire brushing and soaking with penetrating oil for a couple of days.

Alan

Chrisw8 · Apr 25, 2015

good piccies.

I found the two screws, and there were two bolts too. dunno what they were bolted to, .......so they got taken off as well. !!!

I'm thinking of using a wallpaper scraper to get between panels.

keep up the piccies and info on yer thread, as you progress.

Dippypud · Apr 25, 2015

Chrisw8 said:
good piccies.

I found the two screws, and there were two bolts too. dunno what they were bolted to, .......so they got taken off as well. !!!

I'm thinking of using a wallpaper scraper to get between panels.

keep up the piccies and info on yer thread, as you progress.

Take the teeth off of a hacksaw blade and give it a slight 'edge', that'll do it ...

Alantoo · Apr 27, 2015

Chrisw8 said:
good piccies.

I found the two screws, and there were two bolts too. dunno what they were bolted to, .......so they got taken off as well. !!!

I'm thinking of using a wallpaper scraper to get between panels.

keep up the piccies and info on yer thread, as you progress.

Oops! sorry the bolts were listed in the manual it was the screws that were the extras. Should be three bolts there I thinkwill check.

Have you got a copy of the manual? I am sure I have seen it posted somewhere, I can photograph the relevant pages if you cannot find the .pdf

Alan

Disco1 rear quarter removal - help

Chrisw8

Well-Known Member

Chrisw8

Well-Known Member

Chrisw8

Well-Known Member

sam7986

Member

MGBGTV8

Active Member

Chrisw8

Well-Known Member

Alantoo

Member

Chrisw8

Well-Known Member

Dippypud

Never Knowingly Understood

Alantoo

Member

Similar threads