- Posts
- 44,865
- Location
- Hornchurch
I did but spell check had different ideas.
Defender TD5 110 Rear Recovery Points?
- Thread starter bankz5152
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 16,479
Know that feeling....
Also H and J are next to eachother on the keyboard...easily done!
bankz5152
Well-Known Member
- Posts
- 9,311
- Location
- South London/North Kent
Hahahaha I would and I dont mind the idea of Jates but they can be a little tough to get to sometimes! Considering the chassis legs could be burried before the xmember, then again before I head out could always fit a strap...
I quite like fit and forget, but tbh this works for me so far.
But i must ask, everyone says "do not use the lashing eyes on the front/back" Now is that down to the eye itself or the bolt? As Jate rings use the same bolt wich to me is pretty small!
I quite like fit and forget, but tbh this works for me so far.
But i must ask, everyone says "do not use the lashing eyes on the front/back" Now is that down to the eye itself or the bolt? As Jate rings use the same bolt wich to me is pretty small!
Last edited:
- Posts
- 44,865
- Location
- Hornchurch
Land rover now call them towing eyes which is a marked change. I wouldn't recover a stuck vehicle off em though.
They were always lash down points on the chassis. Regarding your original post, I wouldn't use just the rear cross member, hence belt and braces LR design with using chassis and the rear cross member to support towing You need to keep in mind it needs to tow up to 3 odd tonne. I would adjust your driving style
Also keep in mind if you have replacement cross member/extensions that you may well not have the appropriate re-enforcements to cater for this e.g crush tubes.
- Posts
- 44,865
- Location
- Hornchurch
They were tying down points but are now towing points. Maybe the newer chassis are stronger?They were always lash down points on the chassis. Regarding your original post, I wouldn't use just the rear cross member, hence belt and braces LR design with using chassis and the rear cross member to support towing You need to keep in mind it needs to tow up to 3 odd tonne. I would adjust your driving style
Also keep in mind if you have replacement cross member/extensions that you may well not have the appropriate re-enforcements to cater for this e.g crush tubes.
neilly
Well-Known Member
- Posts
- 20,000
- Location
- Oxfordshireness
@bankz5152
I take it you are not going to mod the old towing point as it looks like it is for sale....
What have you decided on?
Cheers
I take it you are not going to mod the old towing point as it looks like it is for sale....
What have you decided on?
Cheers
bankz5152
Well-Known Member
- Posts
- 9,311
- Location
- South London/North Kent
@neilly y I am not! lol I had a look at it last night, while that mod works for a 90 it does not work for a 110, especially with a tank guard in place. The support arms/brackets just dont like up what ever what you put them, even cutting and drilling wouldnt help.
Decided to go for a NAS style rear step, with a bolt on hoop as pictured before. The idea being the NAS step is bolt in through the middle of the xmember, each end of the xmember as well as chassis support arms/brackets. Should spread the weight of any recovery while not ruining the departure angle.
Thats the idea anyway...
Decided to go for a NAS style rear step, with a bolt on hoop as pictured before. The idea being the NAS step is bolt in through the middle of the xmember, each end of the xmember as well as chassis support arms/brackets. Should spread the weight of any recovery while not ruining the departure angle.
Thats the idea anyway...
Last edited:
- Posts
- 1,692
- Location
- towie hell
- Posts
- 1,692
- Location
- towie hell
If you havent ordered it yet dont get a nas step, it was a band aid by rover for american regs.
It sits low er than the crossmember and traps dirt and ruins departure angle
bankz5152
Well-Known Member
- Posts
- 9,311
- Location
- South London/North Kent
well balls. Ordered today, always liked the look of them. It cant sit lower than the current hitch, that was barely off then ground!
FlyingPete
Well-Known Member
- Posts
- 1,305
- Location
- Coventry
I'd fit a DixonBate type of towing pin to the step once you've fitted it. You can get a 5T rated one which attaches with four bolts so should be strong enough as a recovery point. Also handy for when you do need to tow something as you have the jaw/pin and a standard ball hitch.
bankz5152
Well-Known Member
- Posts
- 9,311
- Location
- South London/North Kent
I highly doubt im ever going to tow anything, never had to in the past 5 years, cant imagine i ever will tbh
Similar threads
