200tdi Land Rover 90
Active Member
- Posts
- 78
- Location
- Cheshire
Too many timesWe have all been there!
we'll learn one day
Defender 90 rear anti roll bar links
- Thread starter 200tdi Land Rover 90
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
we'll learn one day
200tdi Land Rover 90
Active Member
- Posts
- 78
- Location
- Cheshire
Unless you drive your Landy on the road regularly, in which case they stop it from listing like a torpedoed ship when you go round corners at any reasonable speed.[/QUOTE]
I would love to just leave it but i use it on road quite regularly so need it to hug those corners
200tdi Land Rover 90
Active Member
- Posts
- 78
- Location
- Cheshire
May I recommend Keswick green? Oh wait, everyone has thatOh no certainly not, one likes to be different
- Posts
- 4,549
I would love to just leave it but i use it on road quite regularly so need it to hug those corners
Standard landrovers tip over @ 50 degrees .... thats takes a lot of speed around a tight corner.
Leave them off and drive carefully
Dr Strangeglove
Well-Known Member
- Posts
- 705
- Location
- Lancashire
Another possibility would be to drill a hole in the flat face of the nut that is easy to access. Start small (5mm or so), then possibly onto 7, 9, etc - just don't brake the drill! This will potentially make it easier to chisel but may also relieve the strength of the nut so may make it easier to turn without chiselling.
Heat is always good, but you currently have the potential to loosen the tapered section which will just have it spinning when you try to undo it.
If it does start to spin, welding something to that end will be a good call.
Heat is always good, but you currently have the potential to loosen the tapered section which will just have it spinning when you try to undo it.
If it does start to spin, welding something to that end will be a good call.
200tdi Land Rover 90
Active Member
- Posts
- 78
- Location
- Cheshire
Hi, cheers for your advice. Thankfully I have managed to get it done. I just used a lot of heat and WD40. Eventually, I was able to undo the nut and the split pin broke off as I undid the nut.
Dr Strangeglove
Well-Known Member
- Posts
- 705
- Location
- Lancashire
That's a great result. We certainly learn lessons as we do this maintenance thing (well I hope I have learned from it!!).
200tdi Land Rover 90
Active Member
- Posts
- 78
- Location
- Cheshire
You're right! Feels great to get the job done in the end right?!
My next task was to replace the front and rear prop shaft UJs. I thought I could do it with a hammer and socket but they will not budge
taking it to a local mechanic to press them out!Hicap phill
Well-Known Member
- Posts
- 16,242
- Location
- Wiltshire
Make sure you buy the correct UJs there are 2 sizesYou're right! Feels great to get the job done in the end right?!
My next task was to replace the front and rear prop shaft UJs. I thought I could do it with a hammer and socket but they will not budge
200tdi Land Rover 90
Active Member
- Posts
- 78
- Location
- Cheshire
I measured them so hopefully I’m capable of thatMake sure you buy the correct UJs there are 2 sizes
- Posts
- 22,904
- Location
- In the next Glen
I measured them so hopefully I’m capable of that
Just chop them off with your grinder oh wait...lol
Glad you got the arb issue sorted.
200tdi Land Rover 90
Active Member
- Posts
- 78
- Location
- Cheshire
That grinder needs to be decommissioned ahah!Just chop them off with your grinder oh wait...lol
Glad you got the arb issue sorted.
- Posts
- 22,904
- Location
- In the next Glen
200tdi Land Rover 90
Active Member
- Posts
- 78
- Location
- Cheshire
Sure, if you’re in the market for an Aldi special buy grinderJust donate it to someone who can use it properly
- Posts
- 22,904
- Location
- In the next Glen
