De cat and mot issues
- Thread starter Swappyd
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 6,593
- Location
- uk
See 8.2.2.1(a) in the attachment
adrian hogg
Well-Known Member
- Posts
- 410
- Location
- WEST MIDLANDS
custom exhaust downpipe with a small vortex silencer will go on my td5 when the one fitted gives up. You could always put several turns of exhaust bandage round the new de-cat pipe where the cat would be
- Posts
- 7,877
- Location
- East Midlands
For what it's worth, back in 2012 I put a stainless steel exhaust on my TD5 Defender. It doesn't have a cat or any suggestive bulge on the downpipe and no one has ever said anything about it at the 9 MOT's I've been through since. And the tester isn't a friend either!
Henry_b
Think outside, no box required.
- Posts
- 15,506
- Location
- somewhere else
If it had a cat from the factory then by law it should have one fitted, I guess the caveat is like my TD5 D2 it didn't have one from new then it's ok....
My Daimler is the same.
My Daimler is the same.
KISSMYAURA
Well-Known Member
- Posts
- 2,799
- Location
- KENT
wot @Brown said........
for me 7 MOT's stainless de-cat exhaust (no bulge) and EGR bypass all good, did make sure it did not look too shiny for the first MOT, etc
i doubt if they even conciously look for it unless you have as ASBO sounding exhaust / gone a bit bright silicone pipes crazy under the bonnet, if it looks to be heavily modded they might look a little deeper, but as i said plain sailing this end!
for me 7 MOT's stainless de-cat exhaust (no bulge) and EGR bypass all good, did make sure it did not look too shiny for the first MOT, etc
i doubt if they even conciously look for it unless you have as ASBO sounding exhaust / gone a bit bright silicone pipes crazy under the bonnet, if it looks to be heavily modded they might look a little deeper, but as i said plain sailing this end!
rob1miles
Well-Known Member
- Posts
- 3,565
- Location
- Slough and Bath
Who knows, my hunch is that it will build up slowly. At some point they will link the vin codes to ID CAT vehicles then make a specific check and fail any that have mods. Industry will support it because they will sell a lot of hours and expensive cats. Could be popular with many voters too as it will be sold as reducing emissions for "legacy" vehicles during the run out to EV. If I had a de-cat vehicle I'd be on the look out for a used OEM system to put in the shed just in case so I don't have to pay premium if there is a problem.
TheMunster
Active Member
- Posts
- 357
Agreed, at some point it will come into public discussion and that will be that. Same with stuff like egr blanks etc
KISSMYAURA
Well-Known Member
- Posts
- 2,799
- Location
- KENT
EGR blanks, simple leave in situ and place blanking sheet in line, remove butterfly inside EGR....
DECAT get a pipe with a bulge or use the genius idea of exhaust wrap above....
MOT testers cannot remove stuff to look inside, ever seen a lamborghini MOT being done?
does no take long, cos the underside is like a sheet of smooth metal, end to end, you cant see a single thing, and they dont brake machine test 4x4's so its lights and emissions and wipers and PASS...lol
rob1miles
Well-Known Member
- Posts
- 3,565
- Location
- Slough and Bath
Never forget that it is the Government that makes the laws. If they decide they are not getting what they want they will write laws until they do. The word missing from your (correct) analysis is "cannot remove stuff to look inside at the moment". That can be changed with a few taps on a keyboard in Westminster. The question that no one can answer is "how blatant does the abuse have to be to trigger a change in the law?" There's an interesting potential for a sting in the tail too: a modest penalty for those with modified exhausts and emissions, a much tougher penalty for those who have taken deliberate action to conceal the modifications. Gentlemen; place your bets.
flat
Well-Known Member
- Posts
- 9,075
- Location
- Far away from you!!
mine is braked tested every time - either a tabley meter or a 4 wheel tester - depending on which of the 2 test centres I take it to
My MOT guy always says, once he has "done" the rest .... "Right, lets take Mr Tapley for a ride round - see what he has to say" ...
ronsealdeath
Sagging Member
- Posts
- 1,851
- Location
- Swansea, Wales
Just remove it and if it fails refit it. Simples.
- Posts
- 44,832
- Location
- East Dorset
According to the law, if you have no proper roller brake tester you have to use a Tapley meter.
If your tester isn't doing that then he is breaking the law.
See this.
https://www.gov.uk/guidance/mot-ins...ht-commercial-vehicles/1-brakes#section-1-2-1
- Posts
- 44,832
- Location
- East Dorset
Bollox. That's illegal. They should use a decelerometer.
see https://www.gov.uk/guidance/mot-ins...ht-commercial-vehicles/1-brakes#section-1-2-1
flat
Well-Known Member
- Posts
- 9,075
- Location
- Far away from you!!
yeah i know, one place uses a tapley (no roller) and the other place uses a 4 wheel roller (but no tapley)
I prefer the 4 wheel roller as it does front back and side to side and gives a reading for each wheel and the handbrake. Identified a weak caliper front left last mot - although it was within spec it was starting to seize
- Posts
- 44,832
- Location
- East Dorset
Yer, I wish my place had a 4 wheel roller too, for exactly the reason you gave. But then they are dead reasonable and helpful so it's pick and choose time. I would like to think I could feel a caliper starting to seize. Deffo on the front but maybe not so easily on the rear.
dunno reeely!
KISSMYAURA
Well-Known Member
- Posts
- 2,799
- Location
- KENT
.
- Posts
- 44,832
- Location
- East Dorset
.
Similar threads
Freelander 2 (LR2)
Couple of issues with my 07 FL2.
