Disco 2 D2TD5; upper left rear light cluster, position light failure

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
RogerStenning

RogerStenning

Active Member
Posts
245
Location
South London
As per the title, the rear left position light has failed. Now, this came back in the MOT as a dim bulb, and when I took it apart to see if there was something obvious, that's when it failed completely.

It's not the bulb (replacement didn't work either), and it's not the bulb holder (got hold of another and tried that too, same fault), so it's something else, and while I have a hunch, I'd like to hear your thoughts.

Any ideas?
 
Verify with a bulb with wires attached and connected across body and the coloured wire and if it works well this way the earth is the problem, if it dims it means it's bad contact on the feed circuit somewhere and the voltage drops under load even though with the multimeter is OK if you see what i mean
 
The "position light" is what is usually called the tail light. It's a twin filament bulb, one for the lower power tail light and the other for the brighter stop light.
The format of these lights can give rise to some misunderstanding regarding the connections. The most important connection is the earth which connects to the body of the bulb and then the pips on the bottom connect one to each filament.
Failure of the earth can give rise to some apparently inconsistant results. If the wiring is intact, the most often cause of the fault is the connection on the inside of the bulb holder not making a good contact with the body of the bulb. Clean the inside of the bulb holder with a bit of abrasive paper
 
That was the first thing I did, with some switch cleaning spray. I'm beginning to think the connector may be a bit iffy, but I'll get a chance to have a better look at things on Sunday (next day off).
 
brian47 said:
The "position light" is what is usually called the tail light. It's a twin filament bulb, one for the lower power tail light and the other for the brighter stop light...
Click to expand...

Ah. Missed this the first time around. Not on the pre-facelift D2s (1998 'S' - 2004 '04' plates); these have single filament position, stop, and reversing bulbs, see http://www.allbrit.de/UNI.cfm?PAGE=820006&SPRACHE=EN
 
Just a quick update. It's not the bulbs. It's not the bulb holder. Both have been swapped out or replaced, the same fault manifests.

Here're the two wiring diagrams, off RAVE.
exterior-lights-page-1.png

exterior-lights-page-2.png



As you can see, the left and right rear tail lamps are shown as twin single-filament lamps, and share each cluster with the reversing lamp and the stop (foot brake) lamp. Each cluster shares a common ground. Each cluster is connected via a four-pin weatherproof connector, and is routed to the light switch on the steering column via a fuse (11) and a couple of headers (0295 & 0707). All of which, before the final connector, are hidden behind various trim panels, housing, or bodywork. Worst case, I have to dig out each darn header to check it in turn. This has the potential to be a complete and utter female hound of a job to work out.

Sunday is my next day off, so I'll have a look then. First thing I'll be checking is the path to ground, of course, then the voltages. After that, if still no joy, the fuse (it's not that, the other bulbs, Stop & Reversing, work just fine), and by a process of elimination, each of the damn buffers. I just hope it's not the darn loom :eek:
 
OK, conclusion posting.

It was the fuse.

I decided to follow the circuit from the fuse box backwards, rather than disassemble things unnecessarily. First thing I looked at was fuse no 11 in the drivers foot well fuse box. It was blown so utterly completely and totally that it'sd almost a textbook example of a blown fuse. a full third of the fuse link in the plastic casing was missing :eek:

Anyhow, I've replaced the fuse, and the lamps are working again :D

Sometimes, it's the simple solutions. Have to remember that next time :)
 
You started this thread the wrong way then cos F11 is not only for the rear LH light is for the front side light and marker(in the indicator) too and you didnt say anything about these only about the rear one cos if we knew that the whole LH side light circuit is dead the fuse would have been the first call :confused:
 
TBH, I never noticed if those were working or not; I never run on just side lights, I always go straight to position 2 and dipped headlights, which were still working. I dare say that had I noticed the front lights gone as well, I would have automatically checked the fuse first off. Bit of tunnel vision on the fault finding there, I guess. Like I said, simple solutions ;)
 
Forgot to mention. Both front side and marker lights are working; no idea what caused the fuse to blow, but I'll be keeping an eye on things. Thanks for the help and advice, all :D
 
RogerStenning said:
Forgot to mention. Both front side and marker lights are working; no idea what caused the fuse to blow, but I'll be keeping an eye on things. Thanks for the help and advice, all :D
Click to expand...
In theory you should trace the fault that caused the fuse to blow before replacing it otherwise for all you know it's still there waiting to do it again.It didn't do it for no reason
 
You must log in or register to reply here.

Similar threads

R
Rear Fog Light Not Working
Replies
13
Views
2K
RustyDefender
RustyDefender
T
Rear spring stuck in upper seat
Replies
14
Views
624
Twinnie
T
ryan_1993
Defender 90 CSW - Rear door brake light not working
Replies
3
Views
576
Anaconda
A
TheYellowLandy
SIII - Brake warning light issues
Replies
9
Views
1K
TheYellowLandy
TheYellowLandy
Blob
L322 Fixed (Sort of) - Every single module in fault. Where to start?
3 4 5
Replies
81
Views
12K
Mark Piercy
Mark Piercy
Back
Top